Adamw 1,015 Posted October 17, 2020 Report Share Posted October 17, 2020 Is now available on the Link website here: https://www.linkecu.com/software-support/pc-link-downloads/ Mostly bug fixes, but more complete release notes here: http://www.linkecu.com/pclink/Link Engine Management PC Link Updates October 2020.pdf iecku.tavea racing and SchuKingR 2 Quote Link to post Share on other sites
Confused 22 Posted October 17, 2020 Report Share Posted October 17, 2020 Thank you for fixing the Cruise Light functionality, I'm hoping that should help with being able to change to a different E-Throttle Target Table to minimise speed overshoot when accelerating. Plus I can have a light on the dash, too! SchuKingR 1 Quote Link to post Share on other sites
Monsterbishi 3 Posted October 19, 2020 Report Share Posted October 19, 2020 Why did they remove the trigger scope image save button, is that just built into the log save section now? Quote Link to post Share on other sites
Vaughan 62 Posted October 19, 2020 Report Share Posted October 19, 2020 Just the image save removed, the log is much better than an image to deal with Quote Link to post Share on other sites
ozyvr4 0 Posted October 20, 2020 Report Share Posted October 20, 2020 I saw more parameters added to the generic can stream. Was ethanol content added? I have a Haltech IC7 and it does not have ethanol content in there list for the link template. Im hopeful. Quote Link to post Share on other sites
Adamw 1,015 Posted October 20, 2020 Author Report Share Posted October 20, 2020 Yes, Ethanol, APS, and a whole lot of statuses from cruise/traction/antilag etc have been added on to the end of the existing generic dash stream. This means older devices (G4 etc) are still compatible with a dash that supports the new modified stream. The detail is in the help file. You should pass it on to them - I believe another user already has but I assume the more that chase them the better your chances. SchuKingR 1 Quote Link to post Share on other sites
EvocentriK 0 Posted October 21, 2020 Report Share Posted October 21, 2020 On 10/20/2020 at 8:10 PM, ozyvr4 said: I saw more parameters added to the generic can stream. Was ethanol content added? I have a Haltech IC7 and it does not have ethanol content in there list for the link template. Im hopeful. Can't you just add it in? I added some parameters that the Generic dash didn't have to send to my Plex display. Unless the issue is you cannot configure the Haltech end? Quote Link to post Share on other sites
FIS 0 Posted November 17, 2020 Report Share Posted November 17, 2020 Please help, I downloaded Ver 5.6.8.3671 install and run then tried to update Xtreme ECU but there is no firmware 5.6.8 on the available firmware list, the latest was v5.6.7 firmware 5.6.7.3631 which is the same as in ECU. Quote Link to post Share on other sites
Kato 1 Posted November 17, 2020 Report Share Posted November 17, 2020 I tried to download English/Japanese version of G4+. But all links are English/Chinese ver. Can you fix the links? Vaughan 1 Quote Link to post Share on other sites
Vaughan 62 Posted November 17, 2020 Report Share Posted November 17, 2020 Has been fixed, thanks MichaelR32GTR and Kato 2 Quote Link to post Share on other sites
Tim D 14 Posted November 24, 2020 Report Share Posted November 24, 2020 I found that my CLL trim tables were missing after the last software update. I noticed a reported bug on the forum. On the downloads page I see: Ver: 5.6.8.3671 (Released: 10th November 2020) – View release notes The release notes say: PCLink version 5.6.8.3666 | DLL version 3659 | G4+ Firmware Version 5.6.8.3668 The choice of languages was... English/日本語 English/Español English/中文 I chose the first option, is it a typo that it says English/日本語? The file that downloaded was: PCLink G4+ EN-JP V5.6.8.3669 Setup.exe How do I get Ver: 5.6.8.3671 to hopefully resolve the issue? Please can you help? Quote Link to post Share on other sites
Vaughan 62 Posted November 24, 2020 Report Share Posted November 24, 2020 V5.6.8.3671 firmware is included in the v5.6.8.3669 PCLink so install the PCLink G4+ EN-JP V5.6.8.3669.exe file and upgrade your firmware using the "Firmware 5.6.8.3671.LFM" file which is included in that install. I'll poke the website guy about getting those release notes fixed. Quote Link to post Share on other sites
Tim D 14 Posted November 25, 2020 Report Share Posted November 25, 2020 Thank you, much appreicated. I installed the latest PCLink and updated the firmware as you suggested. I did experience some strange behaviour though: A while back, I set Lambda Mode OFF to do some refinements to fuel table Once complete, I set Lambda Mode Auto Mode (Wide Band) and the following tables were missing: CLL Pos Trim CLL Neg Trim CLL Update rate I found that by setting FTrim Tables to OFF, then back to 3D Table again, the missing tables re-appeared. Not sure if this is expected behaviour but it confused me. Vaughan 1 Quote Link to post Share on other sites
Vaughan 62 Posted November 25, 2020 Report Share Posted November 25, 2020 looks like those tables allocate and deallocate correctly when connected to the ECU but don't when not connected, have added it to the buglist. Quote Link to post Share on other sites
Tim D 14 Posted November 26, 2020 Report Share Posted November 26, 2020 Thanks for the update. I since noticed that the file compare tool displays incorrect data for these tables. I can share some files if you can't reproduce this? Quote Link to post Share on other sites
Adamw 1,015 Posted November 26, 2020 Author Report Share Posted November 26, 2020 Most likely you have different GP tables allocated so the compare wont work correctly. It relies on the same GP table being used. You can see what tables are allocated near the bottom of the ecu settings menu tree, under table allocation. Quote Link to post Share on other sites
Tim D 14 Posted November 26, 2020 Report Share Posted November 26, 2020 Thanks Adam, you're right, different tables were allocated. Quote Link to post Share on other sites
rbjett 0 Posted December 20, 2020 Report Share Posted December 20, 2020 On 10/20/2020 at 7:48 PM, Adamw said: Yes, Ethanol, APS, and a whole lot of statuses from cruise/traction/antilag etc have been added on to the end of the existing generic dash stream. This means older devices (G4 etc) are still compatible with a dash that supports the new modified stream. The detail is in the help file. You should pass it on to them - I believe another user already has but I assume the more that chase them the better your chances. Adam, are you able to attach an updated generic dash stream to be used with Race Studio 3, I have a few sensors that my G4+ Thunder keeps an eye on and sends their values to my MXS Strada 1.2 over can and it would be great if i could add them Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.