DanielCPG Posted October 26, 2020 Report Share Posted October 26, 2020 Hello. I need to get my Boost Switch (an14) Value accross to my dash via can. Khalid send.zconfig Send to link.khalid.pclr Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 26, 2020 Report Share Posted October 26, 2020 How many positions does the switch have? How do you want the "boost levels" displayed? i.e 0/1/2/3/4... or L/M/H... Quote Link to comment Share on other sites More sharing options...
DanielCPG Posted October 26, 2020 Author Report Share Posted October 26, 2020 It has 3 postions. L/M/H Quote Link to comment Share on other sites More sharing options...
DanielCPG Posted October 26, 2020 Author Report Share Posted October 26, 2020 Also I would like to Send accross My coolant Pressure Value. thanks Quote Link to comment Share on other sites More sharing options...
DanielCPG Posted October 27, 2020 Author Report Share Posted October 27, 2020 Sorry and i need Ethanol % sent accross to ecu. I have made some changes here is an updated file khalid New Send.zconfig Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 27, 2020 Report Share Posted October 27, 2020 Ok, Eth content and a few extras have been recently added to the MXS stream so update your ECU firmware to the latest 5.6.8 and that should work. Coolant press and boost position are sent to the dash in a 2nd stream. I have changed your boost switch set up in the ECU a little so that it uses a cal table to create a "switch position" rather than just working on raw voltage. Low boost is position 0, med is position 1, high is position 2. You may need to set up the voltages in cal 7 to match whatever voltage your switch outputs. In the dash these 0/1/2 values will be translated to LOW/MED/HIGH. I have also attached the CAN protocol file (**.xc1) that you dont actually need, but you can import into RS3 if you want to see how it is done. Khalid new CAN.zconfig LINK_DanielCPG2_@20200121_055456_001949.xc1 Sendtolink.khalid New CAN.pclr Quote Link to comment Share on other sites More sharing options...
DanielCPG Posted October 27, 2020 Author Report Share Posted October 27, 2020 Hello Adam. Ill look more into the Lambda config, but atm The boost switch and coolant pressure signal doesnt seem to be transmitting accross Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 27, 2020 Report Share Posted October 27, 2020 I just took another look and dont see any obvious mistakes. In the RS3 live measures screen do both those channels show "-" ? On the ECU tab in your dash config, does it show "DanielCPG2" as the ecu type? Quote Link to comment Share on other sites More sharing options...
DanielCPG Posted November 16, 2020 Author Report Share Posted November 16, 2020 On 10/27/2020 at 12:16 AM, Adamw said: I just took another look and dont see any obvious mistakes. In the RS3 live measures screen do both those channels show "-" ? On the ECU tab in your dash config, does it show "DanielCPG2" as the ecu type? Coolant press shows --- Bar, However boost sw shows no Value or dash lines, It just shows a blank space and # Link - DanielCPG2 is the ecu type Quote Link to comment Share on other sites More sharing options...
Adamw Posted November 16, 2020 Report Share Posted November 16, 2020 Attach both your current ecu config and dash config and I will take another look. Quote Link to comment Share on other sites More sharing options...
DanielCPG Posted November 16, 2020 Author Report Share Posted November 16, 2020 Ive attatched the files. Also the Lambda 1 value is displaying .07 to . 11. On the current values page this is the value coming from the ecu. If i load up the base CAN stream the Lambda reads correctly. Khaled full tune.pclr Khalid Current Dash file.zconfig Quote Link to comment Share on other sites More sharing options...
Adamw Posted November 16, 2020 Report Share Posted November 16, 2020 That map is password protected, can you unlock it. Quote Link to comment Share on other sites More sharing options...
DanielCPG Posted November 18, 2020 Author Report Share Posted November 18, 2020 Unlocked file.pclr Quote Link to comment Share on other sites More sharing options...
Adamw Posted November 18, 2020 Report Share Posted November 18, 2020 Try these, should be fixed now. Khalid fixed Dash file.zconfig Unlockedfile fixed.pclr Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.