cristanggo Posted November 7, 2020 Report Share Posted November 7, 2020 Dear bro, anyone have build this before? I have 1jz vvti with ar70 ,700cc injector , and r8 coil. The engine start normal with coil 1nz. When use coil r8 the signal take turn on/off while start crank. Pin order left to right (grn-signal-grn-12v) thx u for help IMG_2355.MP4 Quote Link to comment Share on other sites More sharing options...
Adamw Posted November 7, 2020 Report Share Posted November 7, 2020 So have you got 4 wires to each coil? The photo is not very clear but I only see 3? Do you get a continuous spark if you use the ignition test mode? Quote Link to comment Share on other sites More sharing options...
cristanggo Posted November 8, 2020 Author Report Share Posted November 8, 2020 Wire coil first only connect 12v-signal-grnd big. ... result nnt cranked last i try connect pin grnd small parallel coil 1-6 tab to head grnd.the result is coil 1 sometimes flares out the fire sometimes does not burn, as well as other coils. For example, I installed the timing light on coil 1 not turning on, then I moved to coil 2 on as well as coil 3-4 on, coil 5 didn't turn on and coil 6 was on. but I tested it using the software link to make it fire. then when it is tried again to replace the unlit coil with the one that is lit there is still no fire. is my ignition order data wrong. please help The picture is when i try to chance coil not fire with the fire one. Result is that life coil has a fire when it is moved to coil 2, witchis dead but the fire does not come out either. 6 hours ago, Adamw said: So have you got 4 wires to each coil? The photo is not very clear but I only see 3? Do you get a continuous spark if you use the ignition test mode? Could help me, if the wiring pinout coil R8 is correct, what is the possibility of mapping software? if so can you please give me a basemap 1jz vvti with r8 coil direct order. thank you Quote Link to comment Share on other sites More sharing options...
Adamw Posted November 8, 2020 Report Share Posted November 8, 2020 5 hours ago, cristanggo said: Could help me, if the wiring pinout coil R8 is correct, what is the possibility of mapping software? if so can you please give me a basemap 1jz vvti with r8 coil direct order. thank you If it runs sparks and runs fine with your 1NZ coils then that would suggest your map/settings are fine and it is more likely a wiring issue. Both ground pins need to be connected to the cylinder head. Are you sure they are R8 coils? Some of the similar VAG coils (usually shorter stem) have the same plug, but different pinout. Quote Link to comment Share on other sites More sharing options...
cristanggo Posted November 8, 2020 Author Report Share Posted November 8, 2020 3 hours ago, Adamw said: If it runs sparks and runs fine with your 1NZ coils then that would suggest your map/settings are fine and it is more likely a wiring issue. Both ground pins need to be connected to the cylinder head. Are you sure they are R8 coils? Some of the similar VAG coils (usually shorter stem) have the same plug, but different pinout. yes dear friends, i bet it's the vag r8 coil. Quote Link to comment Share on other sites More sharing options...
cristanggo Posted November 8, 2020 Author Report Share Posted November 8, 2020 38 minutes ago, cristanggo said: yes dear friends, i bet it's the vag r8 coil. Quote Link to comment Share on other sites More sharing options...
Adamw Posted November 8, 2020 Report Share Posted November 8, 2020 Is your wiring like this: Quote Link to comment Share on other sites More sharing options...
cristanggo Posted November 9, 2020 Author Report Share Posted November 9, 2020 Yes sir, wiring correct i have see on your post before. This video when use 1nz coil IMG_2354.MP4 Quote Link to comment Share on other sites More sharing options...
cristanggo Posted November 9, 2020 Author Report Share Posted November 9, 2020 Done sir thx you .. Quote Link to comment Share on other sites More sharing options...
Adamw Posted November 9, 2020 Report Share Posted November 9, 2020 Does that mean you solved your problem? What was the problem? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.