Santatu Posted January 23, 2021 Report Share Posted January 23, 2021 Hi. I'm new in the forum. I wanted to know how to set a potentiometer for my sequential gearbox. How to configure the gearbox? What analog to use? Quote Link to comment Share on other sites More sharing options...
Adamw Posted January 23, 2021 Report Share Posted January 23, 2021 Any analog input is fine for the gear position pot. You assign the input and calibrate the voltages in >Chassis and body>Gear detection. Set the gear detection mode to Analog position sensor. Configuration of the gear shift cut and blip is done in >motorsport>gear shift control. There are basic guidelines in the help file but gear shift control needs significant experience to set up and tune so I cant really cover that here, I would be writing for a week... I suggest you read the help and work through the set up yourself and ask questions when needed. Quote Link to comment Share on other sites More sharing options...
Santatu Posted January 24, 2021 Author Report Share Posted January 24, 2021 Ok Adamw. Thanks for your answer, I have solved the question. Another question: Is there a "CUSB" cable with the MXG display terminal? These extremes. Quote Link to comment Share on other sites More sharing options...
Adamw Posted January 24, 2021 Report Share Posted January 24, 2021 NZEFI.com have a dash/panel tuning cable similar to above: https://www.nzefi.com/product/nzefi-link-g4-waterproof-mini-usb-wire-ecu-tuning-cable/ Quote Link to comment Share on other sites More sharing options...
Santatu Posted January 24, 2021 Author Report Share Posted January 24, 2021 Thanks for your answer. Regards. Quote Link to comment Share on other sites More sharing options...
dx4picco Posted February 8, 2021 Report Share Posted February 8, 2021 On 1/24/2021 at 9:48 PM, Adamw said: NZEFI.com have a dash/panel tuning cable similar to above: https://www.nzefi.com/product/nzefi-link-g4-waterproof-mini-usb-wire-ecu-tuning-cable/ Is there by any chance a similar one that doesn't have 50$ of shipping to Europe? Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 8, 2021 Report Share Posted February 8, 2021 NZEFI have them custom made and I assume with a large MOQ. I havent seen anyone else stocking anything similar. You could buy a generic USB bulkhead connector and fit your own LTW plug to the ecu end, but it wont be nicely overmoulded etc like these ones. For example: https://www.aliexpress.com/item/4000205751489.html Quote Link to comment Share on other sites More sharing options...
dx4picco Posted April 7, 2021 Report Share Posted April 7, 2021 On 6/22/2017 at 4:31 AM, Adamw said: Ok, I just probed my tuning cable, that pinout above is wrong. Here's what I get: Pin 1 = USB GND Pin 2 = N/C Pin 3 = D+ Pin 4 = D- Pin 5 = VCC Pin 6 = Shield (the metal case on the USB plug) Also be careful where you get your pinout from as I noticed when looking up the USB pinout on google many images have the D-/D+ swapped over. My numbering above is based on the pinout below that I have marked "correct". http://i.imgur.com/q06quMl.png http://i.imgur.com/w116xwo.png So I finally recieved that aliexpress cable, welded the amphenol AU-06BFFA-LL7001 and it connects well to the ecu. spot on Quote Link to comment Share on other sites More sharing options...
Santatu Posted April 7, 2021 Author Report Share Posted April 7, 2021 I bought my cable at NZEFI.com, I have installed it on my board and it does not work, it does not connect to the ecu. Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 8, 2021 Report Share Posted April 8, 2021 You probably should contact NZEFI for help with this since it is not a Link product. It should work no different that plugging in the normal USB tuning cable. Quote Link to comment Share on other sites More sharing options...
Santatu Posted April 9, 2021 Author Report Share Posted April 9, 2021 I have contacted NZEFI and they sent me another replacement cable at cost 0. Serious company for me. Quote Link to comment Share on other sites More sharing options...
Santatu Posted April 19, 2021 Author Report Share Posted April 19, 2021 I have received the new connection cable from NZEFI and it works fine. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.