Ryley Coker Posted February 14, 2021 Report Share Posted February 14, 2021 So I have the WRX2X link ecu G4X installed. I have gone through the entire setup process. I did the ignition test and injector test as well. Performed the trigger setup. Everything is functioning as it should (I think). But the car just won’t start. Any insight would be great as I’m completely stuck at this point. Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 14, 2021 Report Share Posted February 14, 2021 Can you do us a short PC log of it cranking and attach that and a copy of your map here. How to do the log if you dont know: https://www.youtube.com/watch?v=_P1LRANeO4A Quote Link to comment Share on other sites More sharing options...
Ryley Coker Posted February 15, 2021 Author Report Share Posted February 15, 2021 Lets hope I did this right. I have no RPM registering. But the cam and crank sensors have been replaced with the new engine. PC Datalog - 2021-02-14 4;11;07 pm.llgx Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 15, 2021 Report Share Posted February 15, 2021 Please attach your map too. Also, can you do us a triggerscope while cranking, in your log it looks like possibly you have a cam signal but no crank signal. How to do a triggerscope: https://1drv.ms/v/s!AiYbYlZQuRHPmidU5V2CmTcv6t2y?e=jQuErY Quote Link to comment Share on other sites More sharing options...
Ryley Coker Posted February 15, 2021 Author Report Share Posted February 15, 2021 I do not have a base map that I was given. Could that be my issue? TriggerScopeLog 2-14.llgx Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 15, 2021 Report Share Posted February 15, 2021 For your map, when you are connected to the ecu just go to >file>save as to save a copy of the current map. Your triggerscope I dont think you have done right. Make sure you only click the capture button when the engine is already cranking over - not before. Quote Link to comment Share on other sites More sharing options...
Ryley Coker Posted February 15, 2021 Author Report Share Posted February 15, 2021 Lets try this one. Its not showing stuff right and I followed the directions. I attached a screenshot as well. TriggerScopeLog3.llgx base map.pclx Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 15, 2021 Report Share Posted February 15, 2021 You have no signal on trigger 1 (crank sensor). Cam is fine. So most likely wiring is damaged or something is unplugged somewhere. Also, not the cause of your problem, and not relevant at the moment, but FYI, your trigger mode should be set to Subaru V1-6 assuming you still have the original EJ20. Quote Link to comment Share on other sites More sharing options...
Ryley Coker Posted February 15, 2021 Author Report Share Posted February 15, 2021 Well I will dig into finding my wiring issue. And I’ll go change that in the ECU. I’ll reply once I have more info on my wire. Thank you! Quote Link to comment Share on other sites More sharing options...
Ryley Coker Posted February 15, 2021 Author Report Share Posted February 15, 2021 15 hours ago, Adamw said: You have no signal on trigger 1 (crank sensor). Cam is fine. So most likely wiring is damaged or something is unplugged somewhere. Also, not the cause of your problem, and not relevant at the moment, but FYI, your trigger mode should be set to Subaru V1-6 assuming you still have the original EJ20. So here are the updated trigger scopes. I also changed to V1-6. Still no start. Ideas? trigger scope 4.llgx Quote Link to comment Share on other sites More sharing options...
Ryley Coker Posted February 15, 2021 Author Report Share Posted February 15, 2021 IT RUNS! Not very happy BUT it runs! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.