randolph Posted November 9, 2021 Report Share Posted November 9, 2021 Hi guys, just installed a new link can gauge on a customer car and all is set up and working correctly, but i noticed that in the parameter drop down list there is no (egt display)parameter. is this how it should be or am i missing something? Quote Link to comment Share on other sites More sharing options...
Adamw Posted November 9, 2021 Report Share Posted November 9, 2021 Correct, there is no EGT in our generic dash stream or either of the 2 extra streams. You could possibly do a custom config at the Link end and send EGT in place of some other unused channel. Quote Link to comment Share on other sites More sharing options...
randolph Posted November 9, 2021 Author Report Share Posted November 9, 2021 Understood, i will not mess with it. Just needed a confirmation. thank you Quote Link to comment Share on other sites More sharing options...
Julien Posted May 1, 2022 Report Share Posted May 1, 2022 Hi I digged his topic since I’d like to have the EGTs in my CAN gauge.. Are these parameters correct? ID 52, I lowered the rate a 5hz and I created a new stream but should I’ve simply added a frame on one of the existing? Quote Link to comment Share on other sites More sharing options...
Adamw Posted May 1, 2022 Report Share Posted May 1, 2022 The channels the gauge can receive are hardcoded in the gauge firmware, Gear position is already in the main stream but I dont see a nice way to get EGT's in there. Quote Link to comment Share on other sites More sharing options...
Julien Posted May 2, 2022 Report Share Posted May 2, 2022 Sh.t.. ok, I’ll remove that. I’ll send a massage to GaugeArt to see if be any chance a firmware update could be done to add EGTs. Thanks Adam Quote Link to comment Share on other sites More sharing options...
Julien Posted May 16, 2022 Report Share Posted May 16, 2022 Hi Adam, I m in touch with ArtGauge support. They are ready to add the EGTs in the next firmware update but they don’t find a channel for them in the data stream. I used GP Temp 1 and 2 but they are not listed. Could you help? Quote Link to comment Share on other sites More sharing options...
Adamw Posted May 17, 2022 Report Share Posted May 17, 2022 Yeah, we are having an internal discussion how best to handle this. Let me think about it for a few days. Julien 1 Quote Link to comment Share on other sites More sharing options...
Julien Posted May 31, 2022 Report Share Posted May 31, 2022 Hi Adam, did you had time to mind this little problem ? Quote Link to comment Share on other sites More sharing options...
Adamw Posted June 9, 2022 Report Share Posted June 9, 2022 Yes, we have been discussing this with GaugeArt over the last couple of days and have come up with a plan. Your EGT's will be covered and quite a few other GP channels to allow more flexibility for the less common requests in future. Not sure how long their end will take, I think our end shouldnt be too bad. koracing 1 Quote Link to comment Share on other sites More sharing options...
Julien Posted June 10, 2022 Report Share Posted June 10, 2022 You’re the best! Quote Link to comment Share on other sites More sharing options...
Julien Posted July 10, 2022 Report Share Posted July 10, 2022 Hi Adam, any news on that? I still don’t have the gear display fixed.. no firmware update through IOS were the problem seems to have been corrected weeks ago and is deployed for android users.. :/ Unless their is a firmware update procédure that I don’t know (I keep sending the configuration since it seems to check the firmware at this time) Quote Link to comment Share on other sites More sharing options...
Adamw Posted July 11, 2022 Report Share Posted July 11, 2022 They said they were going to send me a beta to test when it was ready so I dont think it is done yet. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.