Jump to content

Fault Code 20/ 3sgte


Kaushik Singh
 Share

Recommended Posts

Fault Code

Description

Cause

Solution

0

No Fault

Everything is OK!

None

1

RPM Limit

RPM limit reached.

The RPM limit was activated.

This fault may occur as part of normal operation if RPM Limit Fault code is enabled.

2

MAP Limit

MAP limit reached.

The MAP limit was activated.

This fault may occur as part of normal operation if MAP Limit Fault code is enabled.

10

13

16

19

22

25

28

31

34

37

40

43

46

49

52

An V1 at 5V

An V2 at 5V

An V3 at 5V

An V4 at 5V

An V5 at 5V

An V6 at 5V

An V7 at 5V

An V8 at 5V

An V9 at 5V

An V10 at 5V

An V11 at 5V

An T1 at 5V

An T2 at 5V

An T3 at 5V

An T4 at 5V

The voltage at the analog input pin has been above the Error High voltage for longer than one second.

Sensor may be faulty.

Temp channel sensor disconnected.

Fault Settings incorrect.

Sensor voltage is going to 5V as part of normal operation but high voltage fault detection is not disabled (Error High).

11

14

17

20

23

26

29

32

35

38

41

44

47

50

53

An V1 at Ground

An V2 at Ground

An V3 at Ground

An V4 at Ground

An V5 at Ground

An V6 at Ground

An V7 at Ground

An V8 at Ground

An V9 at Ground

An V10 at Ground

An V11 at Ground

An T1 at Ground

An T2 at Ground

An T3 at Ground

An T4 at Ground

The voltage at the analog input pin has been below the Error Low voltage for longer than one second.

Sensor may be faulty.

Volt channel sensor disconnected.

Fault Settings incorrect.

Sensor voltage is going to 0V as part of normal operation but low voltage fault detection is not disabled (Error Low).

12

15

18

21

24

27

30

33

36

39

42

45

48

51

54

An V1 Signal Error

An V2 Signal Error

An V3 Signal Error

An V4 Signal Error

An V5 Signal Error

An V6 Signal Error

An V7 Signal Error

An V8 Signal Error

An V9 Signal Error

An V10 Signal Error

An V11 Signal Error

An T1 Signal Error

An T2 Signal Error

An T3 Signal Error

An T4 Signal Error

The signal is not as expected.

Some analog channel functions do checks on the input signal to make sure it is changing as expected (eg RPM and MAP are increasing but TPS did not change or engine idling but TPS at 100%).

Check sensor operation and calibration.

56

MAP at 5V

The voltage at the analog input used for MAP Sensor has been above the Error High voltage for longer than one second.

This fault will be accompanied by a general Analog Input at 5V fault code. Refer to that fault code for more information.

57

MAP at Ground

The voltage at the analog input used for MAP Sensor has been below the Error Low voltage for longer than one second.

This fault will be accompanied by a general Analog Input at Ground fault code. Refer to that fault code for more information

58

MAP Signal Error

The MAP signal was not as expected.

This fault will be accompanied by a general Analog Input Signal Error fault code. Refer to that fault code for more information

59

TPS at 5V

The voltage at the analog input used for TPS Sensor has been above the Error High voltage for longer than one second.

This fault will be accompanied by a general Analog Input at 5V fault code. Refer to that fault code for more information.

60

TPS at Ground

The voltage at the analog input used for TPS Sensor has been below the Error Low voltage for longer than one second.

This fault will be accompanied by a general Analog Input at Ground fault code. Refer to that fault code for more information

61

TPS Signal Error

The TPS signal was not as expected

This fault will be accompanied by a general Analog Input Signal Error fault code. Refer to that fault code for more information

62

ECT at 5V

The voltage at the analog input used for ECT Sensor has been above the Error High voltage for longer than one second.

This fault will be accompanied by a general Analog Input at 5V fault code. Refer to that fault code for more information.

This fault will be generated if the IAT sensor is unplugged and the Error High value is less than 5.00 V.

63

ECT at Ground

The voltage at the analog input used for ECT Sensor has been below the Error Low voltage for longer than one second.

This fault will be accompanied by a general Analog Input Signal Error fault code. Refer to that fault code for more information

64

ECT Signal Error

The ECT signal was not as expected

This fault will be accompanied by a general Analog Input Signal Error fault code. Refer to that fault code for more information

65

IAT at 5V

The voltage at the analog input used for IAT Sensor has been above the Error High voltage for longer than one second.

This fault will be accompanied by a general Analog Input at 5V fault code. Refer to that fault code for more information.

This fault will be generated if the ECT sensor is unplugged and the Error High value is less than 5.00 V.

66

IAT at Ground

The voltage at the analog input used for IAT Sensor has been below the Error Low voltage for longer than one second.

This fault will be accompanied by a general Analog Input Signal Error fault code. Refer to that fault code for more information

67

IAT Signal Error

The IAT signal was not as expected

This fault will be accompanied by a general Analog Input Signal Error fault code. Refer to that fault code for more information

68

Not Used

69

Electronic Throttle Control Max Duty Cycle Reached

E-Throttle duty cycle has been within +/-5% of its maximum value continuously for more than 2 seconds.

In this situation the E-Throttle system is shut down and cannot be restarted until the ECU power has been cycled. There may be something restricting throttle plate movement or the wiring to the throttle motor has been disconnected meaning the ECU has tried to move the throttle plate but has needed to apply to much power for too long.

70

Electronic Throttle Control Max Duty Cycle Reached

The E-Throttle duty cycle has been within +/-5% of its minimum value continuously for more than 2 seconds.

In this situation the E-Throttle system is shut down and cannot be restarted until the ECU power has been cycled. There may be something restricting throttle plate movement or the wiring to the throttle motor has been disconnected meaning the ECU has tried to move the throttle plate but has needed to apply to much power for too long.

71

Electronic Throttle Motor Driver (Aux 9/10) Supply Error.

If the voltage level drops below 7.0V for a continuous period of at least 2 seconds this fault code will be generated. The Electronic Throttle Control will immediately be shut down and will not be allowed to re-activate until the ECU power is cycled. Note this is different to fault code 67 and indicates that Electronic Throttle Control was shut down.

Measure the supply voltage. Check for blown fuses.

72

Electronic Throttle Control Sensor Supply Voltage Error

If the 5V supply is less than 4.85V for a continuous period of at least 2 seconds this fault code will be generated. Electronic Throttle Control will immediately be shut down and will not be allowed to re-activate until the ECU power is cycled

73

Aux 9/10 Supply

The voltage at the Aux 9/10 power supply pin was not as expected.

This error applies to Red Xtreme ECUs only.

The Aux 9/10 power supply may have an electrical fault.

Check Aux 9/10 Supply runtime value (found under ECU Status runtime values). It should read similar to the Batt Voltage runtime value (found under Analog Inputs runtime values).

Check fuses.

Check outputs wired to Aux 9 and Aux 10 are not shorted to ground.

74

Analog 5V Supply Error

The ECUs 5V Out voltage is not as expected.

There may be a wiring fault on the 5V Out pin causing too much current draw.

Check Analog Output Supply runtime value (found under ECU Status runtime values). It should read between about 4.9 and 5.1 volts.

75

Electronic Throttle Position Control Error

Throttle Plate Position unable to track Target Position. In this fault state the throttle plate cannot maintain or achieve the desired target position. The Throttle Plate position and Target Position in steady state condition must remain at ALL times within +/- 2% of each other. When the Target position is changing the excepted tolerance is adjusted based on its rate of change. If this tolerance is exceeded for a continuous period of at least 2 seconds this fault code will be generated.

Redo TPS calibration procedure.

Check Electronic Throttle Control tuning.

Check mechanical operation of throttle actuator.

76

TPS Main and TPS Sub tracking Error

Throttle Plate Position Signal Tracking Error. Expected relative position between TPS (Main) and TPS (Sub) has exceeded the specified tolerance of +/- 3.0% for a continuous period of more than 2 seconds. In this fault state the ECU must assume the throttle plate feedback to be invalid and that a problem exists with either with the TPS(Main) or TPS(Sub) signal. The ECU cannot detect which signal is invalid which means the plate position is effectively unknown and cannot be controlled.

Sensor Fault, test sensor.

Sensor Calibration Fault, recalibrate sensors.

77

FPS Main and FPS Sub tracking Error

Foot Position Signal Tracking Error. Expected relative position between the FPS (Main) and FPS (Sub) has exceeded the specified tolerance of +/- 3.0% for a continuous period of more than 2 seconds. In this fault state the ECU must assume the foot position feedback to be invalid and that a problem exists with either with the FPS(Main) or FPS(Sub) signal. The ECU cannot detect which signal is invalid which means the foot position is effectively unknown. At this point the ECU will force a fault condition value to 5.0%. It should be noted that in this fault condition the ECU still has control over the throttle plate and this will continue to be controlled as normal which also means the Electronic Throttle Control isolating relay will remain ON.

Sensor Fault, test sensor.

Sensor Calibration Fault, recalibrate sensors.

78

Throttle Plate Position (Main) Signal at ground.

TPS(Main) signal has been less then the specified “Error Low” fault condition for this channel for a continuous period of a more than 2 seconds.

Wiring fault.

79

Throttle Plate Position (Sub) Signal at ground.

TPS(Sub) signal has been less then the specified “Error Low” fault condition for this channel for a continuous period of a more than 2 seconds.

Wiring fault.

80

Throttle Plate Position (Main) Signal at 5V.

TPS(Main) signal has been greater then the specified “Error High” fault condition for this channel for a continuous period of a more than 2 seconds.

Wiring fault.

81

Throttle Plate Position (Sub) Signal at 5V.

TPS(Sub) signal has been greater then the specified “Error High” fault condition for this channel for a continuous period of a more than 2 seconds.

Wiring fault.

82

TPS(Main) not selected.

TPS(Main) has not been selected or has been de-selected on an analog channel when Electronic Throttle Control is being used.

Wiring fault.

83

TPS(Sub) not selected.

TPS(Sub) has not been selected or has been de-selected on an analog channel when Electronic Throttle Control is being used.

Wiring fault.

84

Aux 9/10 Driver Fault

Over-Current/Over-Temperature warning from the electronic Throttle Control hardware contained inside the ECU.

This is most likely caused by excessive current draw on the Aux 9/10 channels.

85

Foot Position (Main) Signal at ground.

FPS(Main) signal has been less then the specified “Error Low” fault condition for this channel for a continuous period of a more than 2 seconds.

Wiring fault.

86

Foot Position (Sub) Signal at ground.

FPS(Sub) signal has been less then the specified “Error Low” fault condition for this channel for a continuous period of a more than 2 seconds.

Wiring fault.

87

Foot Position (Main) Signal at 5V.

FPS(Main) signal has been greater then the specified “Error High” fault condition for this channel for a continuous period of a more than 2 seconds.

Wiring fault.

88

Foot Position (Sub) Signal at 5V.

FPS(Sub) signal has been greater then the specified “Error High” fault condition for this channel for a continuous period of a more than 2 seconds.

Wiring fault.

89

FPS(Main) not selected.

FP(Main) has not been selected or has been de-selected on an Analog channel. Electronic Throttle Control has been shut down

Wiring fault.

90

FPS(Sub) not selected.

FP(Sub) has not been selected or has been de-selected on an Analog channel. The Electronic Throttle Control has been shut down

Wiring fault.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
×
  • Create New...