link g4 pnp with Iq3 dash

[andrew37ford]

so i really want to run a iq3 in my car my question is what exactly do i need and what channels will i be able to view on the dash

[Simon]

You will need a correct Vnet unit to suit the G4.

If using the serial interface what is displayed will depend on the dash configuration.

For CAN it will the info in our generic dash file.

[andrew37ford]

 

ok cool so who sells wick cable and if i was to use the CAN then whats displayed in the generic dash file, and if i was to use serial lead can i display any of the channels on the ecu ?

the reason i ask is i want to display oil press, oil temp ,water temp  boost and AFR along with speed gear rpm ect 

[Simon]

Vnet adapters are all through RacePak.

Serial data will seen all parameters and it will be up to the dash what it can display

On CAN using the generic dash file you will see

 

	Data 0	Data 1	Data 2-3	Data 4-5	Data 6-7
Frame 1	0	0	Engine Speed Display (RPM) = Raw Range = 0 - 15000 RPM	MAP Display (kPa) = Raw Range = 0 - 650 kPa	MGP Display (kPa) = Raw -100 Range = -100 - 550 kPa
Frame 2	1	0	Barometric Pressure Display (kPa) = Raw * 0.1 Range = 0 - 200 kPa	TPS Display (%) = Raw * 0.1 Range = 0-100%	Injector DC Display(%) = Raw * 0.1 Range = 0-100 %
Frame 3	2	0	Injector DC (Sec) Display (%) = Raw * 0.1 Range = 0 - 100%	Injector Pulse Width Display (ms) = Raw * 0.001 Range = 0 - 65 ms	ECT Display (deg C) = Raw - 50 Range = -50 - 205 deg C
Frame 4	3	0	IAT Display (deg C) = Raw - 50 Range = -20 - 205 deg C	ECU Volts Display (V) = Raw * 0.01 Range = 0 - 65 V	MAF Display (g/s) = Raw * 0.1 Range = 0 - 6500 g/s
Frame 5	4	0	Gear Position Display (gear) = Raw Range = 0 - 6	Injector Timing Display (deg) = Raw Range = 0 - 719 deg	Ignition Timing Display (deg) = (Raw * 0.1) - 100 Range = -100 - 100 deg
Frame 6	5	0	Cam Inlet Position L Display (deg) = Raw * 0.1 Range = 0 - 60 deg	Cam Inlet Position R Display (deg) = Raw * 0.1 Range = 0 - 60 deg	Cam Exhaust Position L Display (deg) = Raw * -0.1 Range = -60 - 0 deg
Frame 7	6	0	Cam Exhaust Position R Display (deg) = Raw * -0.1 Range = -60 - 0 deg	WBO2 1 Display (AFR) = Raw * 0.01 Range  = 0 - 65 AFR	WBO2 2 Display (AFR) = Raw * 0.01 Range  = 0 - 65 AFR
Frame 8	7	0	Trig 1 Error Counter Display (counts) = Raw Range = 0 - 255	Fault Codes Display (code) = Raw Range = 0 - 255	Fuel Pressure Display (kPa) = Raw Range = 0 - 6550 kPa
Frame 9	8	0	Oil Temp Display (deg C) = Raw - 50 Range = -50 - 205 deg C	Oil Pressure Display (kPa) = Raw Range = 0 - 6550 kPa	Speed 1 Display (kph) = Raw * 0.1 Range  = 0 - 1000 kph
Frame 10	9	0	Speed 2 Display (kph) = Raw * 0.1 Range  = 0 - 1000 kph	Speed 3 Display (kph) = Raw * 0.1 Range  = 0 - 1000 kph	Speed 4 Display (kph) = Raw * 0.1 Range  = 0 - 1000 kph
Frame 11	10	0	Knock Level 1 Display (units) = Raw * 5 Range = 0 - 1000 units	Knock Level 2 Display (units) = Raw * 5 Range = 0 - 1000 units	Knock Level 3 Display (units) = Raw * 5 Range = 0 - 1000 units
Frame 12	11	0	Knock Level 4 Display (units) = Raw * 5 Range = 0 - 1000 units	Knock Level 5 Display (units) = Raw * 5 Range = 0 - 1000 units	Knock Level 6 Display (units) = Raw * 5 Range = 0 - 1000 units
Frame 13	12	0	Knock Level 7 Display (units) = Raw * 5 Range = 0 - 1000 units	Knock Level 8 Display (units) = Raw * 5 Range = 0 - 1000 units	Limits Flags - Refer bit field definition below.