[Jumper Settings for GTR R34]

Im confused by the jumper settings instruction in the manual.

Part 1 : Is black where the switches are or the opposite?

Part 2 : For R34 GTR do I leave the jumper in or take it out?

[GTR R34 G4X Link CAN-Lambda No Reading Problem]

OK problem is fixed! Many Thanks!

[GTR R34 G4X Link CAN-Lambda No Reading Problem]

52 minutes ago, Adamw said:

The one "Link CAN lambda" channel will receive up to 8 individual CAN lambda's. 

Many thanks for the clarification. Will make adjustments and try again later!

[GTR R34 G4X Link CAN-Lambda No Reading Problem]

3 minutes ago, Adamw said:

You've got two channels set to CAN Lambda, you should only ever have one.  Turn one of these off.  

But I have two Lambda in this car?

[GTR R34 G4X Link CAN-Lambda No Reading Problem]

On 1/22/2021 at 4:36 PM, Adamw said:

Can you attach your tune so I can check your settings. 

If you have just one lambda plugged in, and you go to the "CAN Devices" tab on the CAN set up screen and hit "Find devices", does it find the first one?

 

Hi here is the tune attached.

 

[GTR R34 G4X Link CAN-Lambda No Reading Problem]

1 hour ago, Adamw said:

Can you attach your tune so I can check your settings. 

If you have just one lambda plugged in, and you go to the "CAN Devices" tab on the CAN set up screen and hit "Find devices", does it find the first one?

 

It does find both. I can re name them as well. Same if I just connect one Lambda.

But no reading.

Will attach later. Laptop in the garage.

[GTR R34 G4X Link CAN-Lambda No Reading Problem]

I am using G4X for GTR R34 . Running two Link CAN-Lambda . Both connected on CAN 1 using NZEFI Link G4+ / G4X Dual Device CAN Extension Cable

 

I have installed everything and configured in the CAN Setup .

 

But now there is no Lambda 1 or Lambda 2 reading in the PC Link ?

 

[Does Link Control RB26 Idle Air Regulator?]

Does Link Control RB26 Idle Air Regulator? Not the one that you do the idle speed adjustment screw. The one thats for OEM cold start...

[R32 GTR Engine Fan Control]

I cant seem to control the Engine Fan 1 with my Link G4+ PnP, the fan works when I turn on the AC so I know it is not faulty.

But when I change the temperature to turn on Engine Fan 1 theres no difference. Which Aux Output do I need to specify?

[RB26 PRP 12-1 Trigger Settings?]

I am installing the PRP 12-1 Trigger Kit on my friends GTR R32 at the moment. Would like to know what are the settings in the Link ?

And in the installation instruction mentions there may be advantage to grind off one tooth of the 12 tooth disc? https://www.platinumracingproducts.com/wp-content/uploads/2018/12/TRIGGER-INSTRUCTIONS-REV2-H.pdf

[How to tell between i-Series or v-Series?]

On 5/6/2019 at 3:45 PM, Adamw said:

What is the serial number?  If its less that 18000 you have a V-series.  The  V series does not have OBD2 and cannot use a CAN Lambda.

Can I still wire a normal Wideband like Innovate MTX-L ?

[How to tell between i-Series or v-Series?]

On 5/6/2019 at 3:45 PM, Adamw said:

What is the serial number?  If its less that 18000 you have a V-series.  The  V series does not have OBD2 and cannot use a CAN Lambda.

serial number is 10409

[How to tell between i-Series or v-Series?]

My friend has a older Vi-Pec for his GTR R32.

How to tell between i-Series or v-Series? 44 or 88? I assume everything is same with Link G4?

The ECU is locked with password, he wants to add CAN lambda, Boost Soleniod, CAN to OBD.

Is it possible? I see there’s only one CAN port. I read they say there is some problem with earlier models Serial code before 10000, luckily we got one after Serial 10000.

[Sard 650 cc Injector Dead times/ Latency]

Same boat here I have the SARD 534cc 0.85ms dead time and no voltage.

https://www.sard.co.jp/after_eng/products/engine/injector/injector_syasyu.html

 

According to here http://www.mkivsupra.net/vbb/showthread.php?269098-Sard-800cc-dead-times it is at 12v not sure if it is accurate thou