Jump to content

Euen Burke

Members
 View Profile  See their activity

  • Posts

    26

  • Joined

  • Last visited

 Content Type 

Posts posted by Euen Burke

  2. No injector activity after precrank prime.

    in G4x

    Posted

    20 hours ago, Adamw said:

    275 or -85 seems to be a common theme for BMW so you could give that a try.  I dont have any info specific to the M60.

    Thanks, finally set to -75 and got it to run after increasing fuel main slightly and resetting MAP to BAP. No MAP sensor as using ITBs and trying to get decent MAP is difficult.

  4. No injector activity after precrank prime.

    in G4x

    Posted

    Just trying to get first start on a BMW M60 V8.  We get a single pulse on the injectors with "Key On" but then nothing during cranking. All the injectors have been checked using Injector Test and appear to be operating correctly and in the correct order. The initial Key On pulse can be seen using a test lamp and also the injectors can be heard clicking. 

    The base map has been created from a G4+ M60 base map from another M60.  I have had a look through the Pre Crank and Cranking Prime tables and cannot see anything that may be inhibiting the operation.  Map file attached

    Hope you can help. Thanks

    E36 M60 Base Map V3-01 28-10-2022.pclx

  9. Sequential G/box display on Aim dash

    in G4x

    Posted

    I am currently trying to display gear position information from a 6 speed sequential gearbox through a G4X Storm running the latest firmware onto an Aim MS Strada 1.2 dash (Link race version).  The dash is receiving and displaying the gear position information for 1 - 6 but not for Neutral and Reverse.  Oddly though, it will momentarily display N when shifting between the gears.

    The dash has been configured to receive the ECU "Gear" information and appears to be doing that.

    On the Link, the runtime voltages match those measured when the gear position sensor was tested in the gearbox on the bench.  The position information in the Gear Barrel Settings have been set to R(10) and N(11) respectively. 

    Am I missing something?  I noticed in a post on the G4+ forum that there were CAN settings required however those instructions do not seem to apply to the G4X.

    Thanks in advance

    E36 M60 Base Map V3-02 03-11-2022.pclx

  11. Panel mounting USB programming cable

    in G4x

    Posted

    Does anyone know if there is an off the shelf LTW to panel mounting USB connector so that the USB can be dash mounted for easier access.  AIM have provided this on the programming cable for the MXS dash and we would like to replicate it for the Link if we can.  I know that panel mounting back-to-back USB connectors are available but a one-off cable would be much neater. Thanks.

  13. MXS Strada install problems

    in G4+

    Posted

    BMW E36, 2 litre M52 running G4+ Storm.  Config file attached.  Owner ran into problems installing a new Link MXS dash and has asked me to help sort the problem. Dash powers up but there is no communication with the ECU.  Initially found that he had read the B connector upside down so had the CAN connection to 7 & 8 instead of 27 & 28 however even after connecting correctly there is no communication. I tried looking at the CAN bus with a DVM/Scope but there was no sign of any signal on the bus.  I am unsure if it is related but there is no 5 volts on pin 33 on the B connector but there is 5V on the A connector.

    BMW E36 Chris - 19 07 2021.pclr

  14. G4 plug in BMW E36

    in Link G4

    Posted

    Assuming that the original engine was an M50, the information I have shows pin 44 as the ground for engine intake air temperature, engine coolant temperature sensor and throttle position sensor.  The ground wire for those sensors should run to that pin.

  16. Cam trigger set up for BMW M44

    in G4+

    Posted

    Having sorted the M42 and the M44 bottom end with an M42 head, the time has come to set up a "pure" M44.  The M44 differs from the M42 in that the M42 has a single pole cam trigger with the reluctance cam sensor on the exhaust cam where the M44 has a Hall sensor on the inlet cam providing 4 pulses of different durations across the cam rotation (2 crank rotations). Crank trigger is 60-2. Attached images show the cam pulses against the 2 crank rotations.

    Current plan is to install a G4+ Atom.

    Is there any benefit in trying to utilise all the cam pulses or alternatively does the Link provide the ability to mask the unnecessary pulses, retaining one as the primary trigger.

    Thanks.

    M44 timing 1.jpg

    M44 timing 2.jpg

  18. Spikes on Engine Speed triggering rev limiter

    in G4+

    Posted

    Finally got the car back to the track for testing.  With suggestions above the spikes were still present.  Made 3 more changes.  First was a 1mm spacer under the cam sensor (on the suggestion of our tuner) Second was restore Trigger 2 to reluctor and the third was to disconnect an earth wire between the coil harness and the main common earth point on the engine.  The coil harness included an earth to one of the coil mounting screws via what looks like a choke. On the original harness the earth was also duplicated to the block so I left it in the new harness.  The engine now revs freely to the 7k rev limit without any sign of any spikes on the engine speed trace.  What made this so confusing is that we have 2 cars with almost identical setups and only one was exhibiting the problem. Thanks for your help.

  21. Spikes on Engine Speed triggering rev limiter

    in G4+

    Posted

    1. Ignition is sequential. Storm feeds Bosch 4 channel igniter which drives 4 Bremi 11 860 coil on plug coils. We have this almost identical setup on 2 cars but the other one has not been giving this problem.  The only difference is that the other is an M42 which has a different crank sensor which is mounted on the front of the engine sensing off the front pulley (still 60-2).

    2.  5000RPM trigger scope attached.

    3.  Will try that before we get back to the track.  Unfortunately nothing planned for a couple of weeks.

    5a8e50cce4533_M44Triggerscope5000rpm-22022018.jpg.280bb5fe02f50b7f65ffc8ae95df0b58.jpg

  23. Spikes on Engine Speed triggering rev limiter

    in G4+

    Posted

    We are runnning a G4+ Storm on a BMW M44 and seem to be getting random spikes on the crank sensor that are triggering the rev limiter.  See attached log file.  There is not a lot in the log but I think enough to see what I mean.  The M44 uses a 60-2 toothed wheel mounted inside the crank-case, just ahead of number 5 main bearing.  The crank sensor is mounted to through a hole in the block just below the starter motor. 

    We tried another second hand sensor but that made no difference and have now replaced the sensor with a new one and rewired from the connector on the sensor directly to the ECU using new screened cable, bypassing an intermediate connector at the firewall.  The spikes only seem to occur after a few laps racing which seems to indicate that temperature may be an issue however the ECT is not going over 90°C. 

    After looking at a few similar cases in the Forum I am wondering about increasing the "Limit Ctrl Range" for the RPM limit to see if that helps.  Is there likely to be a downside to doing this?

     

    simon log 04022018 race 2.llg

  25. ComLink USB and Windows 7

    in Link G1

    Posted

    Hi Simon. Thanks for the info. I have found the new W7 drivers from Silabs website (it uses a CP2101) and installed them. Firstly I tried in the default folder as specified in the install program however that didn't work, then I tried installing it in the c:\program files\Link\Comlink folder which is the default for the Comlink drivers and still it wouldn't work. When I open the drivers window for ComLink in Device Manager it still says no drivers are installed and cannot see a suitable driver in either the Silabs folder or the ComLink one. I can keep using my old XP laptop in the meantime but would quite like to migrate if I can. Cheers Euen

×
×
  • Create New...