Steven Oakley
-
Posts
6 -
Joined
-
Last visited
Never
Content Type
Profiles
Forums
Events
Gallery
Blogs
Posts posted by Steven Oakley
-
-
My wiring set up:
CA18DET wire colors on the left Link G4 Storm on the right
C.A.S Wiring:
A: Black Wire (Earth) = Trigger 1&2 Sensor Ground White x2
B: Black/White (Power) = +8v Red/White
C: Green/Black (1 Degree) = Trigger 2 Red
D: Green Yellow (180 Degree) = Trigger 1 Black
Injector High Impedance:
Injector 1:
White/Black = Brown/Black
White = 12v switched
Injector 2:
Yellow/Black = Brown
Yellow = 12v SwitchedÂ
Injector 3:
Green/Black = Brown/Red
Green = 12v SwitchedÂ
Injector 4:
Blue/Black = Brown/OrangeÂ
Blue = 12v SwitchedÂ
T.P.S:
Black (earth) = Green (sensor ground)
Light Blue/Red = Yellow/Blue (An Volt 1)
Light Blue/Black = Red/Blue (+5v)
Engine Coolant Temp:
Black/Orange = Yellow (Temp 1)
Black = Green (Sensor Ground)
Bosch 0 280 130 085 (Air Temp Inlet)
Yellow/Brown (Temp 2)
Green (sensor Ground)
Coil Pack  Igniter:
pack 1:Â Red/White = Blue (ing 1)
Pack 2: Red/Yellow = Blue/Brown (ing 2)
Pack 3: Red/Green = Blue/Red (ing 3)
Pack 4 Red/Blue = Blue/Orange (ing 4)
ECU SET UP
A1:Â Engine Fan (hs)
A2: Engine Fan
A3: Tacho
A4: Fuel Pump
A5: Boost SolenoidÂ
AN V2: TPS
AN V3: Wideband (AFR)
AN T1: Engine Coolant Temp
ANT2: Inlet Air Temp
I am not running the air regulator or A.C.C Valve. I Have taken a 13mm pipe from the inter cooler in behind the throttle plate and plated up the A.C.C valve.
Is my C.A.S correct? Also any advice would be niceÂ
-
Hi I have just set my G4 Storm up for 1st time run. All the parameters have been set up how ever at the bottom of the Config page everything is off. How do i turn it on?
Thanks
-
Thanks how would i go about running the on board map, Instead of my M.A.F sensor?
Yes i do still have the igniter
-
Hi iv just gone a got a G4 Storm for my CA18Det
Im running a stroker kit
LC1 wide band Lamba
F.P.R
1000cc High Inpen injectors
Im going to be using the bosh sensor aswell
I dont want to run the map sensor so im going to use the in built map sensor.
Â
Is there anything else that im going to need and is the a base map i can load to start me off?
-
Hi i have a ca18det witch has just been stroked to a ca20det, i also have a 3071r turbo upgeade, 3" exhaust, and uprated inlet and exhaust manifolds. I am looking for injectors around 1000cc. I just wanted to no the cost of the v5 upgrade also can i get a map for a ca20det? Also what else do i need to do so i can plug it into my laptop for tuning also i want to run a map sensor i have a green and white box the chip says D42I2WG 180199 My email is [email protected]
CA18DET Wiring check please G4 Storm
in Link G4
Posted
Ok The Trigger Wires are back to front They should be:
C: Green/Black (1 Degree) = Trigger 1 Black
D: Green Yellow (180 Degree) = Trigger 2 Red