[Electric - sensors problem]

Hi,

Thank you for your help

 

I only powered the trigger sensors and the engine runs well, no 5V issue

Tomorrow I check the remaining wiring and sensors

 

Can I send you the ECU to enable aux IGN 5?

Thanks

[Electric - sensors problem]

I power on the ecu with all wiring connected and only the engine off and the 5v seems ok

the problem comes up with the engine running

[Electric - sensors problem]

Hi,

thanks,

 

I power on the ecu only with pin 3 (+ 12v) and pins 1-2 (Gnd) without connecting anything else and 5V seems stable

[Electric - sensors problem]

hi,

thanks

today I changed both sensors (IAT-ECT) but unfortunately nothing has changed

test2.pclr

[Electric - sensors problem]

Hi,

thanks,

today i checked the wiring and it looks ok

tomorrow I try to change the sensors (coolant sensor and air temperature sensor)

 

I also found another problem I wanted to connect a solid state relay to aux ign5 but the aux does not work

may be a related problem?

thank you so much

[Electric - sensors problem]

Hi,

Thanks in advance

I have a problem, the engine start run but after few minute stop 

I turn off all extra output and input of Vi-PEC TT ecu but no changes

thanks

tt01.pclr Log tt01.llg

[Wiring wmi solenoid]

Hi,

I would like to wiring a wmi solenoid (aquamist fav) to the aux2 of my VPA1 ecu

Solenoid is 12 ohm

Should I add a resistor or something else?

Thank you very much!

 

[Rotary Oiler/CL Stepper 4D table]

 

good evening

I do not know if possible, but if there was a chance to move from a 3D table to a 4D table for better control stepper motor

thanks

[Audi TT 1.8 20V Trigger errors]

Hi,

I use Audi TT PlugIn ecu (VPA1) on s3 with bam engine but i fix the trigger cam with 1 window and the non VVT chain tensioner becouse i don't use the VVT function

The engine run very well, check the engine timing

[injector dynamics setup]

Hi,

Thank you very much!

I upgrade the ecu firmware and I use GM Characterization data tables because with Link Characterization tables the numbers do not match

I use a 2D Deadtime table with fuellab 1:1 regulator 

Is it right? or is better use a 3D Deadtime table?

I set the min effective pulse width to 0.1250ms , is it right?

thanks!!

 

ID1000_GM_EFI_Live.xls

[injector dynamics setup]

HI,
I have a 1.8t TT i88 Vi-PEC board 
I don't found the injector dynamics (ID1000) right data to insert in the table of pulse width adder and minimum effettive pulse width

I have installed fuellab 1:1 boost reference, have i to use a 3D Deadtime table?

Thanks!!

 

 

ID1000 - Link Characterization Tables.xls

[Aux 8 1.8t tt pinout]

Thanks,

Perfect, but then the e-throttle also work?

If work the warranty is not a problem

Thanks

Elia

[Aux 8 1.8t tt pinout]

thanks,

I would use the pins to connect a 6 wires stepper motor CL to control the Haldex valve

I would keep the e-throttle, I would use another aux for e-throttle relay

Is this possible?

thank you so much

Elia

[Aux 8 1.8t tt pinout]

HI,

I have a 1.8t TT i88 Vi-PEC board but i can't find te number of pin refered to Aux 8

I want change the E-Throttle Relay  (aux8) to another aux becouse i use this for stepper motor

Can someone help me?

Thanks