Marnix van Deijk Posted October 4, 2012 Report Share Posted October 4, 2012 Hello, I'm considering the G4 Extreme wire in to power a Subaru EZ30R H6 engine. I was wondering if there are any good base maps available as that could be a deciding factor to go for the Link (instead of say a Syvecs). I have already installed PCLink and would like to get used to the system with an appropriate map before a possible purchase. I will be running the car using a cable operated throttle (so no DBW) probably off a New Age WRX including the IAC. Are the available maps using the original air flow meter? Does using an air flow meter offer any benefit in system performance or ease of tuning? If so I might want to use WRX V1-2 MAF as I have a few of those on the shelf. I am in contact with the Link dealer for my region (Custom Import Arts in Belgium) and information and support has been quite good so far. Best regards, Marnix van Deijk The Netherlands Quote Link to comment Share on other sites More sharing options...
Dtech Motorsport Posted October 4, 2012 Report Share Posted October 4, 2012 Hi We have done plenty of these conversions turboed and non turboed as well as for a base map i can point you in the right direction if you send me an email all of the ones we have done we have done of map and have not bothered with wiring in airflow meters. if you are looking for a map to look at have a look at the ver7 wrx base map as although this is not for a ez30r it will give you an idea of vvt control etc Regards David Heerdegen [email protected] Quote Link to comment Share on other sites More sharing options...
Cameron Bradley1436215391 Posted October 11, 2012 Report Share Posted October 11, 2012 Drop me an email. [email protected] I have an EZ30R base map I'm willing to part with. Currently there is no way to use the MAF sensor for fuel calculations, however I've been working with Link on getting this sorted as I intend to use the MAF for smoother running and ease of tuning. Quote Link to comment Share on other sites More sharing options...
Tony Dobnik Posted December 11, 2012 Report Share Posted December 11, 2012 Building twin turbo EZ30r for 99 wrx with Xtreme ECU, would appreciate any help I can be provided with in regards to map. [email protected] Cheers Quote Link to comment Share on other sites More sharing options...
Insyncro Posted December 16, 2012 Report Share Posted December 16, 2012 Hello, I am a VW Vanagon conversion specialist working on tuning both the EZ30 and EZ36 using the G4 Extreme. Multiple vans have already been completed, dynoed and road tested. My projects are all in compassing, meaning the entire driveline is custom designed and built as they are all wheel drive vans. Low hour motors were sourced, RJES bellhousing adapters have been used to mate the Subaru engine to the VW transaxle. 240mm pull type clutch packs have been used. Porsche 930 flanges and CVs. Larger front disc brake kits and rear disc brake kits designed and mounted to stop these expedition worthy vehicles. Another side project is adapting the Subarugears, 5 speed, reversed ring and pinion transmission mated with these engines and the EG33. I will do my best to share information and collect as much as others are willing to share with me on the tuning of these engines. dylan www.insyncro.com Quote Link to comment Share on other sites More sharing options...
Tony Dobnik Posted December 27, 2012 Report Share Posted December 27, 2012 He guys, I am looking for base maps for ez30R which according to the sensor wiring information http://www.linkecu.com/support/documentation/technical-drawings/G10/view are supplied with the software. I have looked but alas it eludes me Hope someone can help. Cheers, Tony. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.