Jump to content

Edmund T

Members
  • Posts

    38
  • Joined

  • Last visited

Posts posted by Edmund T

  1. Hi all, 

    I recently installed a Fury G4+ in a 1989 Skyline GTR R32. Motor is up and running and all is remaining is the TPS signal to the stock Atessa controller. I have been reading online that I can share the current TPS singal directly to the Attessa ecu and I  will need to possibly output the TPS signal via the Fury AUX for the Attessa . The vehicle now runs on 2WD as the TPS signal is not connected to the Attessa ECU.

    I have attached a diagram of the Attessa ecu pinouts. There are 2 TPS input signals. 

    Can someone advice what is the best way to get the TPS signal to the Attessa unit for it to function?

    Thanks in advance.

    R32 Atessa.jpg

  2. Hey Adam, thanks for helping me with this.  I am running 5.6.7 firmware on the Fury. Base file attached for your reference .

     

    I also upgraded the AIM strada MXG 1.2 to the latest firmware and also the RaceStudio 3 software. The Link Fury CAN H&L are connected to the 14pin connecter pin 7 &8 ( diagram below )

     

    However, I am still getting the CAN errors as initially reported.

    Appreciate any help on this.

     

     

     

     

     

    image.thumb.png.69ecc4868e3e165f83ac08f07cb2b736.png

    MXG 1.2 Strada.zconfig Hadi R32 GTR Basemap 190120.pclr

  3. Gents, 

    I configured the Link fury ecu and AIM Strada MXG as per the AIM documentation. I cant seem to push the simple data ( RPM, ECT, etc) from the Fury to the AIM dash.

    I am getting a CAN error below from the Fury. I am pretty sure I have the CAN- and Can+ wired correctly. Appreciate any advice on this;

    Configs:

    CuY6QJYE-yZYALQFW5tK7JZ3_ZSuJpDusBB_YZ9C4hvn0tPcATxdZ2Gss9jwzqUO3dlnHin47FilfVw24hzk4aJIrB5DP98T79Ih4zal4M1P9LzAtB8qOvJs4eCvN6-44eAx74pk

     

    image.png.18dfef3912124474c38ca982490dbbfd.png

    Dash config:

    image.png.96ff79a4e470cedefcbc87de3e7c4e31.png

     

    CAN ERROR: 

    image.png.b66ded3d145fc8ad0deca09a1daa5d94.png

  4. Hi, Thanks for sharing this info for setting up the trigger.

    I have just setup the same PRP crank and cam trigger kit in a GTR R32 also.  The motor is running Direct fire igniton and Sequential fuel injection. I would like to check  the Ignition Main setup and R35 cvoil spark duration.

    1. Spark edge should be 'falling' but I wanted to check and confirm.

    2. I am also using R35 cop's with this. Do you know if the spark duration for this coils?

    Thanks in advance. 

     

    zoWsP6uqRg7OFvXeEl4D5iTnVHWtdYrDH079cOCepU8kfAuNjM0otSDhVEJlSdv_Dm0x8HVPZ09y_2c9vJ3ofphJ_nzQoj1x9Aix2MAbYKdlt36DIud72G0LXFxDgVybnJI3z212

  5. Hi all, 

    I need some advice on configuring my Link Fury G4+ with a AIM strada MXG 1.2 dash.

    I have read the ecu help files and search the forums but I coudnt find the configuration for the  Fury CAN setup for the AIM Strada 1.2 MXG.

    Current setup on the Fury CAN is : CAN 1,  Mode: User defined, Bit rate :1 Mbit,  Data -Channel 1,  Transmit user stream 1, Transit rate 10hz ,  CAN ID- 1000.

    Only the AIM dash is connected to the ECU Canbus in the vehicle.  I wired the Can +/-  directly from the Ecu and AIM dash. I can power both ECU and AIM dash and connect to them.

    However, form the ECU CAN setup, I cant find the CAN device when I select 'find devices'. This is my main issue, the ECU does not seem to be able to detect the AIM dash

    From the ECU help files, I did find the CAN setup for an AIM MXL Pista but that didnt work either.

     

    Any help is much appreciated!

     

      

     

     

    AIM strada MXG setup R32 Skyline.pdf

×
×
  • Create New...