[Evolink G3 on Mitsubishi Lancer VI 1997 Ck1A]

I will try that. Thank you very much.

[Evolink G3 on Mitsubishi Lancer VI 1997 Ck1A]

Thank you very much for one more time for your help.

Iwant to ask you if you support this extension ecu harness in order to make the cable change and to leave  mine in stock  form.

[Evolink G3 on Mitsubishi Lancer VI 1997 Ck1A]

 Of course it is and i have already read it. But the problem is that this ECU is for evo and the information is to connect it on the exhisting AFM connector. The engine i have does not have a AFM but only map sensor. Is it possible to tell me the pins of of the stock evo ecu and the pins of the evolink to connect it?

Thank you for all your help.

[Evolink G3 on Mitsubishi Lancer VI 1997 Ck1A]

Hello again,

I have in my hands the evolink G3. The Ecu doesn't have an internal map sensor but only an external unit.

How will i connect it because you said that "factory MAP sensor goes to a pin that is not connected to anything in the Evolink"

On its back side has a hidden usb port. behind a sticker.

I attach some pictures of the ECU map sensor and cables.

[Evolink G3 on Mitsubishi Lancer VI 1997 Ck1A]

Thank you for the loom part number. I thought evolink is like linkplus and has Knock control input.

So distributor only needs the appropriate values on software and nothing more.

Is there anything else to have in mind before first start up?

 

 

[Evolink G3 on Mitsubishi Lancer VI 1997 Ck1A]

Do you also offer extension ecu harness for evo in order to add knock sensor or wideband O2 without make any mods on the stock harness?

[Evolink G3 on Mitsubishi Lancer VI 1997 Ck1A]

Thank you for one more time for you useful information and your help.

So distributor needs only software tuning through the ECU?

I will try to find the information about toothed wheel on the distributor and i will ask your help for  calibrations.

Is there something else i need to take care of?

Thank you.

[Evolink G3 on Mitsubishi Lancer VI 1997 Ck1A]

Thank you very much.

I have a manual  transmission so we are fine.

I also have a few questions.

1. How about the dizzy connection?

2.I have also a rear O2 sensor that is not seen in the ecu pinout picture.

3. Tps sensor,air intake temp sensor,coolant temp sensor,ISC motor,crankshaft sensor are in the same pins?

4. immobiliser

(The evolink G3 i want to use is for mitsubishi evo 7-8).

[Evolink G3 on Mitsubishi Lancer VI 1997 Ck1A]

I made a mistake about the ECU model and change it in the first post. I found some more information about the ECU but i need your help as an expert.

 

http://www.kaxlon.com/mcs/manualer/colt_lancer_98_electrical.pdf

pages 52-59

 

 

 

[Evolink G3 on Mitsubishi Lancer VI 1997 Ck1A]

Thank you very much for your reply. Unfortunately i could not find any pinout for my ecu until now except for the number of pins and the number of connectors that are the same as evolink G3.

[Evolink G3 on Mitsubishi Lancer VI 1997 Ck1A]

Hello,

I want to ask you if it is possible to use the evolink G3 on this  car that has an ecu with same (4)pins.

The car is a mitsubishi lancer VI 1997 (CK1A) and has the 4g13 engine 1300cc 12v with map sensor and dizzy.

Stock ecu model:MD328466

 

Thank you very much.