[Using Aux3 as high side]

Hello,

I´m using an AIM PDM 32 and I feed the "+14V Aux 9 and 10" for E-throttle control with a specific power output. What I did is connecting Aux 3 from ECU to a digital input in PDM. When configuring E-Throttle Relay on ECU I set Aux3 as "high when active", and PDM digital input is configured as "Close to batt" with internal pull down (10kOhm). I´ve tested configurations generating a E-throttle fault by moving really fast with my hand the APS and when fault is active, the new state is correctly detected and power output from PDM disconected.

However, now I´m writting this, I realized Aux3 can´t feed as high side (Only Aux 5 to Aux 8). How is this possible? Could I brake my ECU??

Thanks

[Base maps injector timming]

Thanks Adam. It is great talking with you

[Base maps injector timming]

Hello, 

I´m calibrating a 1.8T 20 V AEB Engine and I´m using  Link TT 1.8T Basemap as starting reference. 

I would like to know what criteria have been used to determinate optimun BTDC on this engines. Settings are 330 deg BTDC (Finish angle injection).

I´ve done some calcs according with OEM cams profiles and considering 1mm of lift the point "opening" or "closing", it will finish injection 40 degs after exhaust closing and 12 degs after intake opening.

So depending on rpm and load, injection pulse will take place on open valve or closed valve. On invented idle (1000rpm) I stimated 18 degs of injection for 3ms  so it would take most of the injection period while intake valve is opened (suitable for cold starting)

Do you think this injection timming from base map is best posible por my oem cam application. What about torque?? I use the car just for track

Thank you very much

[Part # for replacement terminals, Link G4+ Fury A & B connectors?]

Hello,

what about 3-1447221-5 for 22 AWG cable? It says it´s also for AMP 1.0 Superseals. Would be suitable as 3-1447221-3 and  3-1447221-4 are?

[CAN Port Xtremme X]

Hello, 

I would like to know if XtremmeX have CAN port connector-cable included in the box or I should buy It alone. In addition, reading G4x manual, I can see there is a gnd pin. Do I need to pin this output somewhere in the AIM PDM or It just enough with connecting Can1H from ECU to CAN1H PDM and  Can1L  from ECU to CAN1L PDM ?

Thank you

[Link Storm X + AIM PDM + ECU Master CAN switch board]

Thank you Adam, your help is very important to me before building my system. I need to be as sure as posible in the harness design stage to do it well 

[Link Storm X + AIM PDM + ECU Master CAN switch board]

Hello Adam, you said all devices should be on same bus, but my questón is. If you make via software reading with PDM from the keyboard, then you could send that information to ECU in other can bus chanel? I talk about info received to send to other bus...

[E-throttle relay and PDM control]

Thats a good idea. So I will prepare serial digital output and inputs between my PDM and ECU to different purposes, but I will work via CAN Bus. I´m doing it to prevent if CANBus give me problems. 

[E-throttle relay and PDM control]

Hello everybody.

I´m installing e-throttle to my link ECU G4x xtremme. I would like to know how Aux Relay Output works. Following manual diagram, I suppose when activated and working normal it closes to ground. So, I would like to know if connecting this ECU Aux output to a pull up digital input in my PDM, I could control a Power Output from my PDM to the specific E-throttle Power Supply (+14V Aux 9/10).

I would like somebody helps me to uphold this.

Thank you guys.

[CANbus Starter Control]

Okay nice !

[CANbus Starter Control]

Thank you both. Adam, you are like an open book!! But, G4+ and G4X have both same Can Bus protocol? I can see AIM has in their manual protocol for G4+ but a technical support man said me he cannot guarantee G4X works as well as G4+. Do you know it?

 

 

[CANbus Starter Control]

Hello!

I've a question, could I do same yoU did with your motec but using AIM PDM 08?