Damien

I didn't even know that there were several MXL models, I'm sending you a photo of the set, but it communicates correctly since I have the rpm and the water temperature active

Hello, I have a Juno CN09 with a k20 engine and a newland sequential box, a G4X Xtreme box and an AIM MXL dashboard. The car is soon settled and I want to put my engaged gears on my Dashboard as well as my oil pressure in Bar, but unfortunately I can't. Does anyone know how to do this via the box? the Dash and the Link communicate in CAN

Thank you Adam, I had a doubt for the lambda. indeed I may have calibrated it upside down, I'll take a picture tomorrow of the sensor, it's not new and you can't see the writing on it anymore

Enregistrement de Données PC - 2022-03-1 6;04;07 pm.llgx Juno k20 001.pclx

I can therefore use a probe like that if to read the afr and use it as an indication? if yes I have 5 files on this probe, you advise me how to connect it I also have a problem with my analogue oil pressure sensor, I have no voltage variation, could it be due to a bad configuration?

okay but so I must use a CAN output for a lambda? when I ordered the G4X XtremeX box I did not know that we could manage the paddleshifts so I ordered another box (MME motorsport) for the paddleshifts. I will I think to use this case for the paddle

ha great, so I just need to connect a 5V sensor ground and a signal on a link input to get the lambda information? Yes Adam that's right pneumatic system

Thanks Adam for your response. I took note. is it possible to have a lambda probe as an indication? or even a simple lambda you need the annex box?

Good evening everyone, I send you the evolution, the car to start! I had several small problems, to begin with I had the ignition switch on OFF, which prevented me from having a spark and an injection, I then noticed that my exhaust AAC sensor had an inversion and I am in sequential injection suddenly I had no ignition and no injection. Thank you all for your responses. I still have to solve 2 problems. I have to configure my oil pressure sensor and a wideband lambda sensor, it's a Bosh LSU 4.9.

I found an insert on the exhaust camshaft sensor, I now have spark and ignition.

I did a start test by toggling the ignition switch settings to all on, but I still have no spark on my spark plug, however when I test my coils independently via link it works Enregistrement de Données PC - 2022-02-28 12;28;34 pm.llgx

I use outputs 10 and 11 for the CAN2 of my Aim mxl which, unless I am mistaken, are configured

Good morning to all, I am sending you the day's progress. I checked my ground of my coils and in doubt I moved my mass. Now when I test my coils with the program I have a spark. However when I try to start the car no spark is produced. I have my crankshaft signal, my air and water temperature are correct, my throttle sensor is also ok. For the engine details, it's a new engine with a preparation, the electric torch is not original to a honda civic type but a custom one. The fuel for the car will be bio ethanol and the injectors are 650cc. I'm attaching a copy of my file I've made some changes K20 Juno.pclx

everything has been temporarily connected, I can take a picture for you but it's not very representative. i use ignition coil from honda civic ep3 k20. for the wiring of the one if I referred to the diagrams of the pinout link of the coil k20 12V-Motor mass- and signal on IGN1,2,3,4. I'll take a picture for you tomorrow once a garage

Good evening to all, I have just finished configuring my new XtremeX G4X box with my Honda K20 engine with a custom electric torch because it is not mounted on a Honda but on a prototype. I have no current error, but during my first test start today I found that I had no ignition of the spark plug, I use original coil honda K20, I tried to test my coils but no spark, I checked my cable, my 12V is well powered, my negative ground is good and my signal cables that go to the box 1 2 3 4 are also well connected to my box to the location. I send you my file. I also attached a photo of the assembly, do not worry it's an old photo there was not yet the coil and the papillion sensor. K20 Juno.pclx

yes. my problem is solved during your first answer thank you. sorry for my bad english

Thank you Adam, I erased the default codes from the log, but not in the ecu

hello to all, small question I have just finished temporarily connecting my G4X XtremeX computer I am in the middle of configuring the computer for a prototype with honda k20 engine. I Loaded the setup for the k20 to get an idea of the basic configuration. when I changed the water and air temperature analog input, it gave me an error message. what I did not have before without taking the base of the setup. Nothing serious I said to myself I will reset the box and start my own setup, but even reset the two water and air temperature error codes Rest I tried to erase them but they come back instantly I don't understand why