motionper

i am trying to activate the ic sprayer from aux 4 and use my map sensor to ground a solenoid by boost pressure but i can't get it to activate no matter what pressure i useÂ

sorry i forgot i need a timer of about three seconds to bring the ramp in from launch boost to a timed boost increasing percentage over time

in want to activate it with my launch control  i run 50 lbs air pressure on the waste gate hat, i need about 25-30 lbs boost which should be about 45%??? about 10-15 lbs on the launch control

i have a g4 storm i use in drag racing only what is the best set up for timed percentage boost i can trigger the timer off an aux output.how do i set up the timer and percentage

having a problem tach signal very erratic on downloads, also trying to trigger record session off rpm will work at idle but if bring rpm up it will not trigger the racepak to start recording, i see i can change the percentage on the tach signal but not sure if this is the problem

how  can i add a shift light to a g4 storm

i am using a two magnet sensor on my input shaft and a single magnet on the output shaft can i use these functuions to record clutch slip and rear wheel rpm and how would i set them up on the  data logger

where can i find some more info on the logging functions, are there any math channels i would like to record clutch and driveshaft speed

i forgot the message says baro not at 5kp

i installed a gm 3 bar map sensor on my g4 Â i turned off an volt 5 and used an volt 4-i tried the 3 bar setting in the menu and it will not calibrate-the numbers from the manufactuer are 1.1-0 volts- 315.5 5 volts- i tried creating a calibration on channel 4 still no go-i went back and turned on an volt 5 for the built in map and it won't calibrate any ideas????

i am running a g4 storm and want to use the boosts controller function, can i set the axis to psi instead of kph?? will i be able to use that axis to set boost???

i installed a storm unit on a v twin, the on screen tach thru the program is correct but my dash  tach will not read it is capable of changing the pulse but i'm not sure what it is

if anyone installs this unit on a v twin odd fire the correct setting for odd fire is 0 and 405 with single crank sensor and a cam sensor-hope it saves someone some time

also what cam sync set up should i use???? maybe this is the problem

i understand the firing order to be 315-405 but no matter what i do the front cylinder is 45 degrees off-I am calling the rear cylinder #1 and have ignition one to that coil-i have tried reversing the triggers and the same result-i can time cylinder one no problem any ideas??? i have tried #1 at 0 and # 2 at 405-315-675 all to no avail

figured out my dilemma i am using a 60 tooth crank wheel and the unit doesn't like it, i have ordered a 24 tooth wheel from you and i think this will cure my problem- right now i have a 12 tooth and my square wave pattern is very poor my tooth width is only 3 mm and i think it may be to small my pattern looks more like a vss reluctor right now,i will keep you informed after i get the new trigger wheel

v twin odd fire- single coils spark on coil set up-if i remove the crank sensor and use a drill and bolt it registers on my screen but using starter no signal but the cam signal works is there a minimum crank speed setting???

launch control does not function on a g4 lightning ignition only controller

is there a way to hold engine rpm with the clutch switch and also  have the upper rpm limit available

any ideas??????? i really would like to use the launch feature, i purchased this unit with this in mind

no communications, power light comes on the gos off g4 lightning

i am trying to configure launch control but it will not allow me to switch on this function or the ant lag function, it will let me configure a clutch switch what do i need to do??????

I AM TRYING TO RUN FOUR COILS SINGLE FIRE, RIGHT NOW I HAVE #1 CYLINDER ON COIL OUTPUT 1 AND 2 AND HAVE CYLINDER 2 COIL ON COIL OUTPUT 3 AND 4 I WANT TO FIRE #1 AND TWO COILS AT ONCE AND # 3 AND 4 COILS AT ONCE THIS IS A G4 LIGHTNING BOX-WHAT FIRING ORDER SETTINGS DO I USE FOR THIS SET UP?? I HAVE A CRANK AND CAM SENSOR