golf-2
Members-
Posts
26 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Blogs
Everything posted by golf-2
-
Ok, the same to wire the injectors?? Then use the mode multi point group injection? Thank you
-
hello, please simple question , using an old blue G4 storm ecu i will use it to run V8 engine as wasted spark COP ,firing order 1 5 4 8 6 3 7 2 so i wire IGN 1 to cyl 1 & 6 , IGN 2 to cyl 2 & 8 , IGN 3 to cyl 3 & 5 , IGN 4 to cyl 4 & 7 is that right? thanx
-
Hello, About the wiring of the Accelerator Pedal Position Sensor from the vw golf mk5 any one know the pinout of it?? this is the factory wiring , but didn't mention the the 5v , signal , ground thanx
-
Ok thanx for support last 2 question is this near cam signal from crank gap can make problem in high rev?? is the arming table is perfect??
-
Hello, the last thing i did , -84 offset , cam hall, rising, is that the right thing?? the signal of the cam is near from the crank gap thanx
-
sorry , what do u mean by change the offset?? trigger offset?? iam using 276 as many m50 non vanos
-
Hello, i change the cam to hall, rising, resistor off, the engine didn't start at all, return to vr , it start but it didn't run smooth as the polarity was reversed Any idea?? thanx
-
ok thanx i will do it hall, but question what is the effect running as this?? as car running normal thanx
-
Hello, this is the last thing i do, hope this is correct, but why crank signal not smooth like privious capture?? thanx
-
hello, this is the last thing a made it , cam is hall , rising, car running normally till rev limit, is that right?? although crank look weird thanx
-
-
-
question plz thae cam signal is for reference of the stroke only??, didn't effect the ignition timing??
-
making the cam setup hall although the sensor is vr?
-
-
I use the TTlink ecu in S3 APY engine and AWP golf mk4 engine with no problem , the cam is 4 window hall sensor like that pic
-
Hello, about the dbw throttle, an error called aps tracking error , i made calibrate for the aps many times, the signal read well but after ride the car for minutes , suddnly the throttle hold to 7% until i shut down the engine and start it again, the throttle worked well any experience about this error??
-
Unfortunately i don't have the wiring, it is single throttle come from the m62tub44 540i or 740i anyone using this with extreme ecu?? thanks
-
Hello, Any one have experience with the m62b44 540 dbw wiring?? ethrottle signal 1, 2, etc?? using link extreme thanx
-
i use vanos bottom end with the stock vanos crank wheel, yes i notice there r gap with the nv cam sync i swapped the cam wires, it read well, i use -325 calibrate, but i have feeling the car advances more than the table i have timing light but i don't know where is the timing mark in the m50s engines thanx for support
-
In the antilag option , AL ign retard mode, degree vs degree absolute , in the (degree) , it will subtract the degrees from the ignition table??example, that mean when i put 0 in full throttle , it did not retard anything?? right?
-
non vanos head thanx
-
I have problem with the m50 engine good stable crank sensor reading , but when enable the cam , the rpm go random erratic using stock non vanos vr cam sensor , setup is reluctor , cam pulse x1 any idea??
-
For the stock non vanos cam sync, what is the right setup for Trig-2 edge and sync mode?? thanks