Gctech
Members-
Posts
38 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Blogs
Everything posted by Gctech
-
Hello, The help section suggest aux 1 and aux 2 to setup a 3 wire IAC ,im already using all aux 1 and 2 for VVT functions and only have 8-10 free in which I assigned Aux 8 to ISC solenoid yet i can control Idle at all, which other way can I set up a 3 wire rotational IAC thanks Base map mk4.pclr
-
I increased the trigger threshold to 6.5 and that seem to do the trick I didnt get any trigger 1 errors anymore, I did the tigger 2 pullup triggerscope you requested thanks 3000RPM PULLUP OFF.llg 3000RPM PULLUP ON.llg
-
Hello I got this random issue with the rpm Limit which is set to cut at 7500 in the main RPM limit table, when I first do a run it works as it should then I get a ecu RPM LIMIT REACHED error , i reset the error do a second pass and my rpm limit drops to 7000 , again remove the error try again and on the 3rd run it drops even further to 6500. what can be causing this? im guess is something to do with the error as if I turn the car off and on i can hit commanded rev limit, I attached main File and 3 logs thanks Base map mk4.pclr 3rd gear full run 2.llg 3rd gear full run 3 early rpm cut.llg 3rd gear full run 4 early rpm cut 6500.llg
-
Hello Adamw Everything is now working correct , the exhaust cams pins were inverted aux 3-4 backwards , I switch them and now cam solenoids are responding correctly. Thanks for all the help!!
-
Hello Adamw I tried the new settings and it definitely got rid of the cam errors, but the exhaust cam solenoids still not responding, I try different offsets based on the CamTest options with out luck. thanks Base map mk3 v3.pclr vvt error exhaust cams solenoid.llg
-
I attached a tiggerscope also the revised map disconnecting LH cam from D1 and leaving it only in Tigger 2 still experiencing same issues. Thanks for the help Trigger Scope Log 2017-05-15 5;00;25 pm.llg vvt errors log 2.llg Base map mk3 v3.pclr
-
I follow the cam test steps to get the offsets is way better but i can not get rid of the "extra pulses" error why does this happens ? where the extra pulses are coming from? also why D4 ehx rh solenoid is at 100% , im a bit lost I have triple check my wiring and is good. I attached the new File revision and a log thanks Base map mk3 mr2 2gr v1.pclr vvt errors log.llg
-
That certainly dis the trick to get a signal, now I think my offsets are off in d2 d3 and d4. What is the procedure to properly setup the offsets?
-
Hello Simon yes as indicated by the wirg 2.2k pull up i added those when I first wired the ecu
-
Ok I got the cam pulse error solved, the trigger 2 vvt was wrong , is not what is in the Help files. The only issue left is that im not getting signal in the other three cams D2,D3 and D4 , these as well as D1 share the same 5v signal and shield ground.
-
Hello , thanks for the response, I when ahead and turn it off D1 ,but im still getting cam signal error , I check power ground at the sensor and all check in good, I attached a screen shot of the error thanks
-
Hello I am setting up my first link Fury, im have a few problems setting up VVT everything else is working correct I get Cam Error in system statuts window. anyone can share some knowledge I have attached the base File thanks Base map mk3 mr2 2gr trigger calibration.pclr
-
Hello Im trying to calibrate a 3.5 kavlico map sensor to Fury ecu and i get a error window that says command fail, any Ideas what can it be? thanks