[K20 vtc wiring and setup]

Ok thanks 

[K20 vtc wiring and setup]

Thanks adamw, vvt working already, do you have the basemap for vvt table? 

[K20 vtc wiring and setup]

Thanks adamw, done all the wiring, engine start ok, need guide on software setting for vvt

[K20 vtc wiring and setup]

Intake cam sensor to di1

Vtc solenoid to aux 2

Exhaust cam sensor to trigger? 

Need 3 wires connected? 

[K20 vtc wiring and setup]

This sensor? 

[K20 vtc wiring and setup]

Ok thanks,

Under inlet bank 1 menu, cam sensor input di1 need to connect to where

 

[K20 vtc wiring and setup]

I would like to set aux 2 for vtc, vtec high/low already set by using aux1

[K20 vtc wiring and setup]

Ok thanks. 

How to configure aux 2 in the link software?  

[K20 vtc wiring and setup]

Request information on k20 vtc wiring and map setup, is the above connection correct? 

[G4x k20 speed sensor]

Thank you

Thank you

[G4x k20 speed sensor]

DI3 connect to gearbox? 3 wire which one? 

I need speed input then when car moving i need send a signal to lock the reverse gear. Pls help

[Monsoon and k20 vtc setting]

New problem  I test aux 1 using a light bulb not working, but aux 6 is OK, is it ecu problem? 

[Monsoon and k20 vtc setting]

Monsoon digital input 1 to intake cam sensor, aux 2 output vtc

When I adjust vtc map aux 2 no working

Digital 3 connect to speed but nothing happen also... 

 

Please help

[linkg4x monsoon k20 link e throttle setup and wiring]

Set to quiet mode, working fine without noise, thank you

 

[linkg4x monsoon k20 link e throttle setup and wiring]

Aux 5 active state set to low already, tps calibration done, but pedal still not working, please help

After aux 5 active state set to low and tps calibration I can see the throttle automatically open then close. After tps calibration done, I press the pedal nothing happened to the throttle 

This map is working when I press the pedal, but throttle not moving

OK I think I found it to work, set when stalled to run throttle and e throttle 1 target map, correct? 

But I notice when I put the key to on position, the throttle making sound, is that normal? 

[linkg4x monsoon k20 link e throttle setup and wiring]

Dear Adamw, is my wiring and setting correct? 

I've done aps calibration, tps calibration got problem. 

[linkg4x monsoon k20 link e throttle setup and wiring]

And then, I have connected pedal signal 1 to an volt 3 and 1 to and volt 4

is this the setting for the pedal signal? 

 

 

 

ive found main and sub already but still not working, which part I did wrong 

[linkg4x monsoon k20 link e throttle setup and wiring]

this is the setting you provided, it's different from mine i have connected an volt 1 to stock throttle pin 6 and an volt to to pin 4, but my software can assign 1 an volt only... 

And then, I have connected pedal signal 1 to an volt 3 and 1 to and volt 4

is this the setting for the pedal signal? 

[linkg4x monsoon k20 link e throttle setup and wiring]

Adamw, e throttle still not working, I've connected e throttle module green wire to aux 4, brown to aux 3,white to aux 5, correct? 

Adamw, e throttle still not working, I've connected e throttle module green wire to aux 4, brown to aux 3,white to aux 5, correct? 

[linkg4x monsoon k20 link e throttle setup and wiring]

Adamw, just to confirm, pedal wiring, do I need to connect to linkg4 ecu，or just take the throttle 6 pin you mentioned b4, no need any connection from the pedal socket 

[linkg4x monsoon k20 link e throttle setup and wiring]

Thanks Adamw, how about the link software setting, need to assign an volt to something? And aux to something  confusing 

Sorry Adamw, the wiring diagram you provided, throttle pin 2, connect to 3 location? E throttle module yellow, ecu 5v and any ecu an volt input, correct? 

[linkg4x monsoon k20 link e throttle setup and wiring]

Please help me with wiring and software setup

 

K20 stock electronic throttle got 6 wire out, I need to connect to where? 

I'm now using linkg4x monsoon and link e throttle module

I need how to setup the software also, too confused with an volt and aux

[linkg4x monsoon and k20]

Yes manual transmission, don't know which wire to cut and link to monsoon, can help? 

[linkg4x monsoon and k20]

Hmm I'm thinking using monsoon for tuning and factory ecu for other function

 

[linkg4x monsoon and k20]

How to wire monsoon parallel with k20 ecu, can someone help