danimin31
-
Posts
23 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Blogs
Downloads
Posts posted by danimin31
-
-
Hi. I’m in trouble with my skyline. I have a map done and need to solve this. Idle is stable but when i press a little the pedal the rpms drops and if i press more it revs without problem but when i release the gas revs drops down until dies. Here are a few starts log and map. rb20good.pclrb20det.llg
-
-
On 3/13/2024 at 3:17 AM, Adamw said:
No, there is no CAN receive in the old G4
But my skyline plugin G4 from 2014 has a CAN port. In my case will be possible to connect the CAN-Lambda module?
-
6 hours ago, Adamw said:
Do you have the ignition mode set to wasted spark? As I mentioned earlier the storm based plug-in only has 4 ign drives so it fires the coils in wasted spark pairs, ign mode needs to be wasted spark as per the base map.
Yes. I have tried with direct spark mode and wasted spark. I follow the manual deleting the ignitor 4 drive too and same. Explosions on the exhaust and intake when stop cranking
-
12 hours ago, Adamw said:
Try a squirt of starter fluid in the manifold to confirm if the issue is fuel or spark. If that doesnt give any more signs of life then get a timing light on it and confirm your base timing looks ok. Your offset looks about normal for an RB though.
I have try this, and doesnt start. The timing its ok, im thinking about a bad ignition config, because sometimes when i’m cranking, it sounds like a explosion on the exhaust and sometimes on the intake.
-
It has 10 litres now, it’s not empty because the reseirvor light its off
-
Hi. I have tried but nothing changes. On the video you can see only when i press accelerator to the floor it want to start.
-
Yes. Now i have spark, yesterday sound like a start try when logging. I continued trying to start but it doesnt start.
-
Hi Adamw here they are:rb20det.pclrb20 fail with map.llg
-
Today i had tested another G4 with same map and doesnt start.
-
The engine still does not start. Still having not spark.
-
-
-
I restore it to factory settings and did an update and nothing changes
-
Sorry. That is the wrong map. This is the correct one: Also my Ecu Status is not as yours:
-
This is the last i have testNissan RB20DET.pcl
-
Is the stock gts-gtr from link g4
-
Any ideas?
-
And here is the log with pin16 grounded:
-
I have checked, the LED doesnt turn off when cranking, but the fuel pump doesnt sound and the rpm doesnt move with Pin16 at ground
-
Yes. Is the old G4 from 2014. I have checked it today and the answer is no. When i crank it, the LED turn off and 2 seconds later it turns on again as you can see on the second video
-
Hi. I recently bought a Link G4 GTS/GTR plugin ecu for my R32 GTST Skyline. The engine is full stock apart of a T3 turbo, front GTR intecooler and FFP. The engine wiring loom is new from wiring specialities and the engine runs with the stock ecu.
With Link ecu I follow all the instructions from the manual and when the engine cranks, the computer disconnects from the ecu, and the engine dont start, i think that its missing spark because i tried to start with ether and nothing happen. I’m using the base map that comes with the ecu and i config triggers and other parameters. Also i read some posts with similar problems, and i try to put pin 16 to ground and it stays connected because i can see the triggers and engine speed for a moment but when i try to start the ecu restart because the fuel pump sounds again and the rpm on tacho do the check as when i put on contact position. Other thing i tried is to put battery 12v to pin 45 as i saw on other posts, and doing this, the fuel pump doesnt sound and the rpm dont move.
I try other maps downloades from this forum but nothing changes.
Any ideas or suggestions?
Rb20det idle/acceleration problem
in Link G4
Posted
Running well on fuel and ignition 14.3 afr on idle