[Firmware upgrade issue]

Ok will give it a try

[Firmware upgrade issue]

C/program file(86)/pclink/linkg4plus/

Ok so this is error message

[Firmware upgrade issue]

Won't let me upgrade firmware 

says to run the loader again

cannot create a file

id upload a screen shot but won't allow it

[Can't upload screen shots]

only got 1.28mb to upload a pic ? How come ?

[CAN Lambda compatibility with i88]

Ok mate thanks for that, top info as usual

[CAN Lambda compatibility with i88]

Cheers Adam how do I roll back to the 5.0.1 if there are issues ? 

[CAN Lambda compatibility with i88]

Right ok Is it ok to update to the latest firmware on this ecu I have took the screen shot of and can I save the current firmware just incase?

[CAN Lambda compatibility with i88]

Can I use the Can Link with a i88?

This

 

[evo 8 idle fluctuation]

So I have a evo 8 with a pnp on it, with an AMS intake and unknown similar style throttle body, using the air screw to set base idle, but now and then fluctuates to the point of cutting out, any tips on sorting this?

icv steps currently set to 500

 

[Base idle set screw Evo]

Thanks gents

[3 port boost solenoid setup]

Is there anyway I can click test the 3 port on a evo 8 pnp? everything seems to be plumbed and setup right just no matter what duty I put in boost doesn't increase just wanted to test the circuit, thanks

[Base idle set screw Evo]

What is the best way of closing the stepper fully?

[CAN Lambda Issues]

UPDATE-

New CAN Lambda arrived today, plugged in, setup, job done, must be faulty unit.

[Base idle set screw Evo]

Ok does screwing the airscrew completely in sort this?

[CAN Lambda Issues]

When I spoke to simon I had already run power direct from a battery source and tested continuity on my can line which tested ok, the out put voltages though on the can line were constantly stuck at 0.34 and 0.1v no change no matter what, which he suggested replacing the unit.

[Base idle set screw Evo]

To set base idle, just a case of key on, disconnect ICV, start up and adjust to attain correct base idle?

[CAN Lambda Issues]

I have this 

[CAN Lambda Issues]

Can you confirm the pinout for this plug? I'm using the white as can hi and the green as can low

[CAN Lambda Issues]

Spoke to Simon in technical and run through some ideas and come to the conclusion to swap out the CAN Lambda, will update.

Simon has been very helpful on this matter!

[CAN Lambda Issues]

I have followed to the letter the setup instructions but cannot connect to the CAN lambda, putting it in CAN1 slot just makes the ecu disconnect. I am then unable to reconnect, put it in port CAN2 and it doesn't auto disconnect but still cant connect. Any help?

To add rechecked power and rechecked wiring. 60 ohms on can line

 

[Evo 8 260 non start]

Sorted was pin swap

 

[Evo 8 260 non start]

Yes mate I saw that but applies to evo 4 only

Just been informed will possibly apply to 7-8 the pin swap so going to try 

[Evo 8 260 non start]

Vehicle starts fine on stock ecu. On G4 I cant hear pump working, is their a known pin swap required before I start getting stuck in?

[Is my injector calculation sound]

Right this is for Evo 6 - base map - fuel equation is traditional with master fuel at 12ms for stock 560cc injectors

542/1015=0.53

12*0.53=6.36

new master fuel, 6ms for id1000?

Enter relevant dead times in 2d table.....job done?

 

[Injector dead times ref chart]

Nice one David very interested in your findings!

PCLink Help > G4+ ECU Tuning Functions > Fuel > Fuel Setup > Injector Setup > Injector Information also has some info.

Scott

Checked out the help files but nothing with common injectors such as RCs or IDs