Jay00 Posted August 5, 2019 Report Share Posted August 5, 2019 Hi, I've recently picked up a GaugeArt Canbus gauge. However, it's the Haltech version... Upon connecting to the gauge, Link G4+ is not showing as an ecu option, only, you guessed it, Haltech. Is there a way to configure the CAN output to suit this scenario? Appreciate any guidance. Thanks, Jason Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 5, 2019 Report Share Posted August 5, 2019 Yep, the branded gaugeart devices are locked to that particular brand ECU in the firmware. The Link CAN is flexible enough to be able to duplicate the Haltech stream however there is a limitation of six ID's (haltech uses many more in their full stream). If you attach a copy of your tune and a quick list of the channels you would like to be able to display I should be able to set it up (may not be able to give you the full channel list that is avail in the gauge). Quote Link to comment Share on other sites More sharing options...
Jay00 Posted August 6, 2019 Author Report Share Posted August 6, 2019 Thanks for the speedy reply and offer AdamW. Guess I've just learnt something the hard way! The below x6 would be great: Coolant Temperature (An Temp 1) IAT (AN Temp 2) Oil Pressure (AN Volt 5) MAP Sensor (AN Volt 1) Fuel Pressure (AN Volt 6) Ethanol Content (DI5) + AFR/Global Knock/Voltage on the chance there's more space... Thank you. - Jason 190803 Tune.pclr Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 6, 2019 Report Share Posted August 6, 2019 Try this, I got all of your list in there except battery volts. 190803Tune with Haltech CAN.pclr Jay00 1 Quote Link to comment Share on other sites More sharing options...
Jay00 Posted August 6, 2019 Author Report Share Posted August 6, 2019 23 minutes ago, Adamw said: Try this, I got all of your list in there except battery volts. 190803Tune with Haltech CAN.pclr 163.02 kB · 1 download Legend. They've popped up now. Thank you kindly! Quote Link to comment Share on other sites More sharing options...
JonoP Posted January 13, 2020 Report Share Posted January 13, 2020 Hi Adam! Thank you for this. I have mostly sorted out a customer that made the same mistake buying a Haltech GaugeArt for his Link G4+. I have set up the ones you have specified but I might need some more. The customer requested these: - Battery Volts - TPS - Oil Temperature - injector duty - RPM I think all I need is the CAN IDs. Where did you get these from? Also, oil pressure is reading incorrectly. It reads -14 when there is no pressure so is it possible it's readiing absolute? I tried to offset but unsuccessfully. Thanks! Quote Link to comment Share on other sites More sharing options...
Adamw Posted January 13, 2020 Report Share Posted January 13, 2020 6 hours ago, JonoP said: Also, oil pressure is reading incorrectly. It reads -14 when there is no pressure so is it possible it's readiing absolute? I tried to offset but unsuccessfully. Yep, I think they do use absolute. Try an offset of 1013. 6 hours ago, JonoP said: - RPM - TPS Add Eng speed and TP main to same stream as MAP, as below. 6 hours ago, JonoP said: - Oil Temperature Add oil temp to same stream as IAT and ECT as below. For injector duty and batt voltage you would have to give up some of the other channels as you only have 6 CAN IDs to play with and haltech spread them over many more. 6 hours ago, JonoP said: I think all I need is the CAN IDs. Where did you get these from? Copy attached. Haltech-CAN-Broadcast-Protocol-v2-0.pdf Quote Link to comment Share on other sites More sharing options...
JonoP Posted January 25, 2020 Report Share Posted January 25, 2020 Thank you very much Adam! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.