Hermit Posted November 11, 2019 Report Share Posted November 11, 2019 I’m just curious if I could run the Zeitronic CAN Bus ZT-3 on my link ecu? Or is the Link’s own Canbus lambda my only option? The Ecu is a p&p altezza link G4+ Thanks Quote Link to comment Share on other sites More sharing options...
Adamw Posted November 11, 2019 Report Share Posted November 11, 2019 Yep, that works fine. I can help you setup the CAN setup when the time comes. Take a look at the 14point7 Spartan 3 as another decent low cost option. Quote Link to comment Share on other sites More sharing options...
Hermit Posted November 11, 2019 Author Report Share Posted November 11, 2019 26 minutes ago, Adamw said: Yep, that works fine. I can help you setup the CAN setup when the time comes. Take a look at the 14point7 Spartan 3 as another decent low cost option. Thanks Adam which of the 2 would be the better system? I think I’m better going with canbus lambda over the analog type? Quote Link to comment Share on other sites More sharing options...
Adamw Posted November 11, 2019 Report Share Posted November 11, 2019 Definitely CAN over analog any day. I havent personally used the Zeitronic one but he has been around for years and I have never heard any bad comments about his stuff. I have installed and used quite a few of the 14point7 ones with no drama and they seem reliable too. Quote Link to comment Share on other sites More sharing options...
Rossobianconero Posted November 14, 2019 Report Share Posted November 14, 2019 Talking about info vía CAN, with a Atom2 G4+, i know i can send information vía can to my dash (aem cd5 with logger), the question can i send information that Is not wire To the ECU but Is wire To the dash (oil temp, oil pressure, exhaust temp) be send to the ECU vía can from my dash? Quote Link to comment Share on other sites More sharing options...
Adamw Posted November 15, 2019 Report Share Posted November 15, 2019 7 hours ago, Rossobianconero said: Talking about info vía CAN, with a Atom2 G4+, i know i can send information vía can to my dash (aem cd5 with logger), the question can i send information that Is not wire To the ECU but Is wire To the dash (oil temp, oil pressure, exhaust temp) be send to the ECU vía can from my dash? List below of currently supported inputs via CAN. So Oil press is there, exhaust temp is there (would go to one of the "CAN TC Cyl#" channels), but there is no oil temp CAN input. If you just want to log it or use it for safeties etc then you could bring oil temp in as say "CAN TC Cyl 8", you would still be able to use it for anything you can use oil temp for but it would just be named wrong. And yes the AEM dash can send this info to the ecu - however the AEM dash doesnot have any analog inputs - how are you wiring these sensors to the dash? Quote Link to comment Share on other sites More sharing options...
Rossobianconero Posted November 15, 2019 Report Share Posted November 15, 2019 19 hours ago, Adamw said: List below of currently supported inputs via CAN. So Oil press is there, exhaust temp is there (would go to one of the "CAN TC Cyl#" channels), but there is no oil temp CAN input. If you just want to log it or use it for safeties etc then you could bring oil temp in as say "CAN TC Cyl 8", you would still be able to use it for anything you can use oil temp for but it would just be named wrong. And yes the AEM dash can send this info to the ecu - however the AEM dash doesnot have any analog inputs - how are you wiring these sensors to the dash? Well the oil temp Is actually not that important because has never been really a problem, if the dash shows the oil temp Is More than enought, i can wire the sensors With a External module that you wire To the dash Is actually aem to. The guys at aem said that it can't be done. That the dash can send info but not that kind of info. If you have done it ir try it i Will like to know. Quote Link to comment Share on other sites More sharing options...
Adamw Posted November 16, 2019 Report Share Posted November 16, 2019 Actually you are right, it seems they have removed the CAN transmit functionality, Im sure it used to... Anyhow, it will still work no worries, the ecu will read the CAN data direct from the expansion module, it doesnt need the dash. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.