Altubi Posted August 19, 2020 Report Share Posted August 19, 2020 G4+ Atom Engine 4.5 1fz fe I Set fuel mode to multipoint group, set ignition to wasted spark Test ignition Ok Set trigger But on spark when running engine Before engine it running good Anoth person set it I reset factory ecu Quote Link to comment Share on other sites More sharing options...
Altubi Posted August 19, 2020 Author Report Share Posted August 19, 2020 If map sensor not calibration Get spark or no? Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 19, 2020 Report Share Posted August 19, 2020 Do you have valid RPM showing in the software when you are cranking it? Quote Link to comment Share on other sites More sharing options...
Altubi Posted August 19, 2020 Author Report Share Posted August 19, 2020 No RPM (0) No signals Meby wire? But before worked Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 19, 2020 Report Share Posted August 19, 2020 Correct, if you have no trigger signal showing you have a wiring issue. What ecu is it? Does it have a triggerscope function? Mexi193 1 Quote Link to comment Share on other sites More sharing options...
Altubi Posted August 19, 2020 Author Report Share Posted August 19, 2020 Atom Don't have triggerscope My trigger offset Correct? Quote Link to comment Share on other sites More sharing options...
Altubi Posted August 19, 2020 Author Report Share Posted August 19, 2020 Anoth problem Map don't calibration 5kpa Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 19, 2020 Report Share Posted August 19, 2020 You need to select the correct calibration for the MAP sensor that you are using. The 5 KPa error means your calibration doesnt match. Quote Link to comment Share on other sites More sharing options...
Altubi Posted August 20, 2020 Author Report Share Posted August 20, 2020 If don't calibration map sensor can I get signals ignition? Test 2 map sensor Link map sensor and factory map sensor Link sensor 1.41 volt Factory 3.4 volt and use cal5 with factory sensor I tried Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 20, 2020 Report Share Posted August 20, 2020 The MAP sensor will not prevent trigger, but you still need a working MAP sensor for it to run. 27 minutes ago, Altubi said: Test 2 map sensor Link map sensor and factory map sensor Neither of those sensors is a Link sensor. 1 is a GM/Delphi sensor, but it could be 1,2,3 or 4Bar as they all look the same. The factory 1FZ MAP sensor usually matches the ST185 calibration but if yours is outputting 3.4V it is doesnt sound like it is the normal 1FZ sensor. You will have to find a MAP sensor with known calibration, it is the most important sensor for engine control so you cant just guess. Quote Link to comment Share on other sites More sharing options...
Altubi Posted August 20, 2020 Author Report Share Posted August 20, 2020 @Adamw@Adamw thank you solved problem map sensor Now I get signal RPM But give me error trigger 1 I expect it need to adjust the offset trigger or something else Quote Link to comment Share on other sites More sharing options...
Altubi Posted August 21, 2020 Author Report Share Posted August 21, 2020 (edited) @Adamw I get signals RPM But trigger 1 error What is problem? Edited August 21, 2020 by Altubi Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 21, 2020 Report Share Posted August 21, 2020 Attach a log of it cranking and your map. Quote Link to comment Share on other sites More sharing options...
Altubi Posted August 21, 2020 Author Report Share Posted August 21, 2020 I will learn to attach the record Quote Link to comment Share on other sites More sharing options...
Altubi Posted August 23, 2020 Author Report Share Posted August 23, 2020 Good morning @Adamw Or any one help me Can you see this log1.llg 1fz-1.pclr Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 23, 2020 Report Share Posted August 23, 2020 Please take a look at your trigger settings again, they are nothing like the settings I told you to use that you have included in your first post. Tooth count should be 36 and trigger 2 sync mode should be cam pulse 1x. Quote Link to comment Share on other sites More sharing options...
Altubi Posted August 23, 2020 Author Report Share Posted August 23, 2020 Yes, I put trigger 2 you told me first time , but it never gives a signal whith it When but none i get signal canceled cam sensor before Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 23, 2020 Report Share Posted August 23, 2020 You still need the correct tooth count. Quote Link to comment Share on other sites More sharing options...
Altubi Posted August 24, 2020 Author Report Share Posted August 24, 2020 Number of teeth 36 - 2 I do not know what to do As for trigger 2 Cam plus 1 or none Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 24, 2020 Report Share Posted August 24, 2020 2 hours ago, Altubi said: As for trigger 2 Cam plus 1 or none Either will work since you are running wasted spark and multipoint fuel. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.