nicksak1 Posted August 24, 2012 Report Share Posted August 24, 2012 Hi Guys, I was hoping i can get a base map for a supra 2jz gte vvti manual with direct fire IGN and dual electric cooling fans. Also if someone can guide me on repining for dual cooling fans and boost controller. From what i can see I have only one AUX open(Aux3) on the vvti patch harness. I was going to add two aux outputs for fan high and boost controller. Thank You Nick Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted August 24, 2012 Report Share Posted August 24, 2012 Can you list what Aux outputs are being used and what they drive. You mention Patch Harness, do you have a 2JZ wiring loom adaptor to suit a V88 that connects directy to the original 2JZ connector. Quote Link to comment Share on other sites More sharing options...
nicksak1 Posted August 24, 2012 Author Report Share Posted August 24, 2012 Sorry that's what i meant. Im using a wiring loom adaptor for vvti that plugs directly into the jdm harness AUX 1-Cam control solenoid GND AUX 2-Fuel pump controller signal AUX3- OPEN AUX4-Wastegate Solenoid -ve AUX5-Fuel pump controller +5v signal AUX6-Canister purge VSV -ve AUX7-EGR valve -ve AUX8-Throttle motor clutch -ve AUX9-Throttle motor - AUX10-Throttle motor For the direct fire i replaced: (A10) Inlet gas regulator valve -ve is now IGN 4 (B13)Engine check light -ve is now IGN 5 (B12)Fuel pressure regulator VSV -ve is now IGN 6 Im using the coils and igniter that came off my previous 2jz-gte usdm. Do you recommend anything differently. Sorry about the guest post. Ill input my serial number tonight. Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted August 25, 2012 Report Share Posted August 25, 2012 Post your email address please, for file transfer. Dave. Quote Link to comment Share on other sites More sharing options...
nicksak1 Posted August 25, 2012 Author Report Share Posted August 25, 2012 [email protected] Thanks Dave Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted August 25, 2012 Report Share Posted August 25, 2012 Hi, Base Map sent. I have activated your outputs for Fan High Speed and Boost solenoid. You will need to reconfigure the rest of the Auxillary Outputs to suit your setup. Also while ONLINE to the ECU, set IGNITION OUTPUTS 4,5 and 6 to ON. They are still OFF in the base file. Dwell table has filled values to suit standard coils. Hope this helps. Regards Dave. Quote Link to comment Share on other sites More sharing options...
nicksak1 Posted August 25, 2012 Author Report Share Posted August 25, 2012 Thanks Dave sounds good. The email is missing the attachment. Please resend Thank Again Nick Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted August 25, 2012 Report Share Posted August 25, 2012 Hi Nick, you have mail. Dave. Quote Link to comment Share on other sites More sharing options...
muzzytt Posted May 30, 2013 Report Share Posted May 30, 2013 Hi Guys, I was hoping i can get a base map for a supra 2jz gte vvti manual with direct fire IGN and dual electric cooling fans. Also if someone can guide me on repining for dual cooling fans and boost controller. From what i can see I have only one AUX open(Aux3) on the vvti patch harness. I was going to add two aux outputs for fan high and boost controller. Thank You Nick Hi Nick You mention you have A PATCH harness for the supra 2jzgte vvti .. may I ask where you got it from? I've just got a v88 and can't find a harness to make life easier. Cheers Muz Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.