Peter Andersson Posted June 8, 2015 Report Share Posted June 8, 2015 Hello , My name is Peter Andersson I have a Link G4+ on my Dragbike ( FunnyBike ) I have a problem getting my link G4+ to talk to my IQ3 Dash Before i updated the firmware it did not show anything . But now some parameters is correct , Watertemp , Oilpressure but the rest is rubbish , Rpm comes and goes Its set to generic dash ( the only preset that has comunication at all )  Lots and lots of hours trying to make this work   ( Andersson Turbo on facebook )  Quote Link to comment Share on other sites More sharing options...
samsul Posted June 9, 2015 Report Share Posted June 9, 2015 Hi Peter, From previous testing on the bench the following setup was found to work well with our ECU's:  To get the software to see the correct I/O options it needs to read the configuration from the Racepak CAN module. - Install the Datalink software and during setup select the IQ3 configuration files - Open “Datalink Program†from the Windows start menu - Go to file → Open car configuration → Select IQ3_config - Go to Settings → Scan COM ports to detect the Dash - Click 'READ' on the toolbar on the right hand side to retrieve VNET module configuration - This will import all the 'EFI' settings which are setup to match the data output from Link/Vi-PEC ECU's. Channels controlled from within the dash (such as GPS speed, accel G's etc) are also automatically available. - Right click on “IQ Logger†to bring up the dash display configuration - Set up each channel with the desired I/O's from the ECU (EFI channels are set to suit the Link/Vi-PEC ECU's) - Any individual setting can have the scaling etc changed if required by right clicking on it on the configuration screen Things to look out for: make sure the parameters you are setting up are on the channels from the VNet module, not the generic ones that show in the list. The one IQ3 we had here for testing did need some tweaking done to the scaling to get some of the parameters to span correctly (for example: MAP: Raw data A = 0, will become = 0, Raw data B = 1, will become = 1. AFR: Raw data A = 0, will become = 0, Raw data B = 1, will become = 0.001) One other thing I found when testing was the data transmit speed on the Link seems to have trouble if it is low-ish. I found a couple of the readings would not show or drop out if it was not high enough. 100Hz seemed to work well. If some data is getting through then it looks like everything is set up and talking correctly. This indicates it is just scaling issues or perhaps the generic parameters selected (rather than the ones from the VNet module). Unfortunately we do not have an IQ3 here to try your configuration with, but we are in the process of getting one. If you continue to have issues the next step may be to try a copy of your setup in one here once we have received one. Regards, Sam Quote Link to comment Share on other sites More sharing options...
Peter Andersson Posted June 16, 2015 Author Report Share Posted June 16, 2015 Im now using Firmware 5.3.1 The problems still remains  I have done all of the above except for the rawdata altering I dont know how to performe that in a metodic way without guessing I dont know if the problem is Racepaks or if it is Link that puts out the wrong signal Quote Link to comment Share on other sites More sharing options...
Peter Andersson Posted June 16, 2015 Author Report Share Posted June 16, 2015 Allso I have the 5.4.0 software and Quicktune does Not work lambda shows wrong , Only in quicktune meny Lambda gauge is correct , mixturetrim = correct  , Data logg the same The letters in some boxes are scrambled ( quicktune window ) Quote Link to comment Share on other sites More sharing options...
Simon Posted June 16, 2015 Report Share Posted June 16, 2015 Hi Peter The dash issue is most likely to be the configuration of the dash as you are seeing some info this indicates the ECU is sending information. Normally if the ECU CAN setup is incorrect you will get no information at all. Can you try 5.4.1 PC link to see if you still have an issue with the quick tune. Â Â Â Quote Link to comment Share on other sites More sharing options...
Peter Andersson Posted July 19, 2015 Author Report Share Posted July 19, 2015 (edited) Does Anyone have a sollution for my Dashproblems It seems like Im in between the manifactures here , no one likes to take resposabillity to this problem. After all Its Not a cheap product The quicktune issue still ramains when using 5.4.1 Regards Peter Edited July 19, 2015 by Peter Andersson Quote Link to comment Share on other sites More sharing options...
Simon Posted July 20, 2015 Report Share Posted July 20, 2015 Hi Peter.Would you be able to take a screenshot of the lambda / quicktune issue.Same would be good for the vnet/dash configuration. If you wanted to send the units to us we can sort on the bench. Quote Link to comment Share on other sites More sharing options...
Peter Andersson Posted July 23, 2015 Author Report Share Posted July 23, 2015 Pic 1 and 2 shows what Q tune reeds in realtime but the A /F shows the actual valuesDash is allso in same realtime watertemp is correct , Oilpressur is correct ( no sensor for the moment ) Rpm works on and off and real Lag ( slow )Lambda A / F allso way of , Box marked Peter shows manifoldpressure allso slow and comes and goesThe config is deffault from Racepak for G4+ Quote Link to comment Share on other sites More sharing options...
Simon Posted July 23, 2015 Report Share Posted July 23, 2015 Hi Peter can you attach you PCL file from the ECU.There was and issue on earlier firmware versions that caused the lambda average to read incorrect when only one lambda input was used.I can then also check the COM settings to the dash Quote Link to comment Share on other sites More sharing options...
Peter Andersson Posted July 24, 2015 Author Report Share Posted July 24, 2015 Where can I send the Map? Thats not for public forum for display Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted July 24, 2015 Report Share Posted July 24, 2015 Hi Peter,I don't know if Simon's email address has changed or not it was [email protected] or [email protected] you can PM him oryou can send it to myself [email protected] .Either way Simon will get it. I can run the file on my simulator and test for you if you wish also and can guarantee strict confidentiality.RegardsDave. Peter Andersson 1 Quote Link to comment Share on other sites More sharing options...
Peter Andersson Posted July 25, 2015 Author Report Share Posted July 25, 2015 Hi Dave that would be nice if you could help me . Do you have a facebook profile or messenger? I can not run Link software on this computer any longer ( it worked before )On the computer that works i can send the file throug messengerRegards Peter Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted July 25, 2015 Report Share Posted July 25, 2015 Hi Peter ,yes my face book page is either David Kriedemanor my ViPEC_LINK_PRO TUNINGRegardsDave. Quote Link to comment Share on other sites More sharing options...
Peter Andersson Posted July 27, 2015 Author Report Share Posted July 27, 2015 Hi Dave , tryed to send you message on Facebook . dont know if you got it? Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted July 29, 2015 Report Share Posted July 29, 2015 Hi Peter,sorry I will check, but I didn't get any notifications.RegardsDave. Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted July 29, 2015 Report Share Posted July 29, 2015 Hi Peter,I have not received anything.Can you send to my email address , [email protected]RegardsDave Quote Link to comment Share on other sites More sharing options...
Peter Andersson Posted September 7, 2015 Author Report Share Posted September 7, 2015 Does anyone have any solution to this problem? Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted September 7, 2015 Report Share Posted September 7, 2015 (edited) Hi Peter,are you still referring to the dash issue.And or the quick tune not working.If you are still having issues with QUICK TUNE let me know and I will log in and check what is happeningIf you can send me your dash configuration file I can look into it more deeply for you.I see the dash can except 20 parameters from the ECU, it also shows the stream ID's etc, so I am not sure if these need to be programmed into the ECU CAN, I would believe so as the Racepak is not setup as a predefined selectable dash config.If this is the case I am prepared to write the stream and help you get this thing going.Please send your dash config file for Racepak software to [email protected]RegardsDave. Edited September 7, 2015 by Dave Kriedeman Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.