Peter Andersson Posted February 11, 2018 Report Share Posted February 11, 2018 Now it loses signal It starts climbing and then down to zero and upp again . Random no pattern Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 12, 2018 Report Share Posted February 12, 2018 Ok, so now try this one. In this one I have removed all bus load and just left the counting RPM/MAP. See if this gives smooth incrementing values with no dropouts. Racepak-dash Test3.pclr Quote Link to comment Share on other sites More sharing options...
Peter Andersson Posted February 12, 2018 Report Share Posted February 12, 2018 Hi , Yes Now it works. No dropouts Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 13, 2018 Report Share Posted February 13, 2018 Ok, it seems your Vnet adapter doesnt like it when we put too much load on the bus. RPM and MAP are the first two bytes of data in the message so for some reason it is too slow to keep up and starts skipping these bytes. So in the file attached to this post I have removed all the redundant channels that you were not using, hopefully that might reduce the load enough to make it happy. RPM and MAP are now real values so the engine will need to be running. Give this one a go and let us know what happens. Racepak-dash Test4.pclr Quote Link to comment Share on other sites More sharing options...
Peter Andersson Posted February 13, 2018 Report Share Posted February 13, 2018 I am so HAPPY now , first time in 3 years IT REALLY works A few followups questions on this If I whant to present more data on the display for any reson it wil not work? If I update Firmware , does this custom setup remain ? Or do i have to get it fixed by you guys every time? What can i say to Racepak? Is the Canadaper not good enough? I am very grateful for the help on this problem and I hope more users can benefit from this , Maybe some sort of preset in the software for the IQ3 Dash Regards Peter https://www.facebook.com/peter.andersson.3152/videos/1644267578990420/?comment_id=1644284985655346¬if_id=1518537274197089¬if_t=feedback_reaction_generic Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 14, 2018 Report Share Posted February 14, 2018 10 hours ago, Peter Andersson said: If I whant to present more data on the display for any reson it wil not work? 3 I only removed stuff that I thought you wouldnt use or that racepak dont read. For instance I dont think you will ever use MAF so I removed MAF channel. Racepak V-net only reads one wheel speed so I removed the other 3. Racepak doesnt read Knock trims so I removed 8 channels of knock. You dont have VVT so I remove 4 camshaft position channels. Etc... You cant add any new data channels that are not normally included in the "generic Dash stream" as the racepak module is fixed and cant be customised by the end user. 10 hours ago, Peter Andersson said: If I update Firmware , does this custom setup remain ? Or do i have to get it fixed by you guys every time No, the CAN set up is now just stored as part of your "tune" file. It will not be affected by firmware updates. 10 hours ago, Peter Andersson said: What can i say to Racepak? Is the Canadaper not good enough? Whatever the problem is, it seems to be unique to you only. My best guess is your Vnet module is faulty but its difficult to confirm without a more in-depth look with a CAN sniffer etc. All I can say is there are many hundreds of these dashes and Vnet modules same as yours out there all working fine with Link ECU's. I have personally set up a couple and they worked right out of the box with no special tricks needed. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.