[AeM 30-2012 Cal]

Hello Guys,

Someone have a Cal for the sensor in object ?

Can I use Standard NTC ?

Can I use the calibration that AeM provides with no pull-up and table with ohms vs °C ?

Thanks

[GrimmSpeed EBC Frequency]

Hello Guys,

Someone knows the correct frequency for GrimmSpeed EBC ?

 

Thanks

[Thunder mask]

Perfect Adam,

One question...the hole from behind is 34 far...from side? 34 too?

[Thunder mask]

On 10/8/2018 at 9:03 AM, Adamw said:

I dont personally have a bracket handy.  I will see if I can get some measurements from someone at head office tomorrow.

Hello Adam,

Have you some measurements forum me?

 

thanks

[CAN to OBD2 on Evo 8]

CAN wires + 12v + Ground (i think is not a sensor ground )

[CAN to OBD2 on Evo 8]

8 hours ago, Adamw said:

The Evo 8 didnt have a CAN bus from the factory, Im pretty sure it uses a single wire K-line type protocol, so it will not have suitable wires already in the harness.  Since CAN needs to be twisted pair wires you will be best to run two new wires from the ECU to the OBD2 socket.

Ok Adam, thanks a lot  

[CAN to OBD2 on Evo 8]

I already saw that schema...i hope that someone knows the pin without test the harness

[CAN to OBD2 on Evo 8]

Hello Guys,

I need to wire the CAN2 of my Thunder to stock harness of Evo 8 (to use the stock OBD2 port).

The Evo 8 pinout says PIN62 and PIN79 are diagnostic ... which one I should user for CAN Lo and CAN Hi?

 

Thanks

[Thunder mask]

Ok perfect.

 

Thanks a lot

[Thunder mask]

Hello Adam,

Have a draw with location of mounting holes?

 

Thanks 

 

[Thunder mask]

Thanks Adam..i think should be fine.

I Will try to make a cardboard 3D model  

Thanks a lot 

[Thunder mask]

Hello Guys,

Someone have a mask with dimension and position of connector for make a wiring harness without ECU ?

 

Thanks

[KnockBlock in PCLink]

Yes...but " Why I have to buy a knockblock when the ECU make the same things? "  

[KnockBlock in PCLink]

Hello,

Should be very useful to have the same functionality of KnockBlock direct into PCLink connecting ear phone direct to pc (or jack direct into ECU for newer products) and listen knock.

I think this features (that adaptronic have) makes more advantages :

- setting the knock control features

- don't wire another knock sensor for knock block to semplify wiring on the dyno/street

- saving money

 

Thanks

Regards

 

[Launch Control and Rolling antilag!]

Thanks for your reply Adam,

it's just for have a complete solution.

Some car tuned for drag racing...often...it used for flying mile or km.

The solution that you adviced is a little trick (couse is not simple to press button at the same RPM every shot on the strip.)

 

 

 

[Launch Control and Rolling antilag!]

Hello,

Why is not possible to use both launch control and rolling antilag ?

All other high-end ecu (Motec, Haltech, Emtron, Microtech, etc) take these functions separately.

Would be very useful to separate these functions to put the tuner in condition to use them at 100% of their potential.

 

Thanks

[CAN Hub]

Yes...you right...the Haltech CAN Hub is a little bit expensive...but this solution with 4 pin is very useful because all devices connected to the Hub is automatic powered up too.

Imho this solution produce a clean wiring harness and a very easy extendable platform :)

 

[CAN Hub]

Hello Guys,

I'm new in the LinkECU world.

I used for a long time Haltech products (ECUs and CAN modules)

The Haltech CAN Hub is very easy and fast way to connect CAN devices...there is a chance to use the CAN Hub with G4+ Fury and others CAN expansion modules? Like wideband controller, I/O expander, EGT controller etc etc ?

 

Thanks

Best regards