semih

can lambda controllers faster than older wideband controllers, i was thinking the same as you, but i changed my mind after buying a can lambda controller.

i used older style aem wideband with g4x but it read wrong, i bought can lambda controller, for example can lambda controller read 13.4 aem read 12.2 i don't trust them other than i'm using bosch combined pressure temp sensors for oil and fuel, i love them

Thank you Adamw, i found 0258 017 169(vag groups are using oem like vw tiguan audi q3 etc.), but i guess it will be break down too lol then i'll try another one

it's working now, thanks for the tip i set driven speed same source by the way, i'm using pd type otg adapter, real dash works on the tablet and can be charged at the same time

hi, i'm using haltech wb1 with my g4x, i guess lambda sensor goes(reading about 6 at wot) bad and i want to change it haltech wb1 came with 0258 017 169(5 wire) numbered bosch sensor i want to use 0281 004 821(6 wire) does it matter whether the sensor has 5 or 6 wires, as long as there is a resistor in the socket? Regards, Semih

i'm seeing driving wheel speed correct in pclink, i choose vss1 but no luck.

Yes, my wheel speed is working on Pc Link. Gear indicator is working on real dash. i'm using your uploaded zip file setup, i tried to stream wheel speed but no success

Hi i connected real dash to my g4x. Everything is ok but i can not set speed, i don't want to use gps i want to use calculated speed but i did not success yet, how can i calculate speed? (i choosed calculated values, speed(gear indicator ratio and rpm)) regards, semih

if you have my99 cam gears(7 teeth), you have to use my99 crank sprocket later engines have 2 teeth cam gears and different crank sprocket

i want to ask another question, can i connect 2 combined sensor to one 5v? i want to use for fuel

when i change target lambda 0.95 shaking is gone, probably my fuel pump is bad my injectors are stock yellow ones, but i want to change somethinng different like bosch or id ones for example when i set my target idle at 900rpm, car is working about 950rpms, like about 50rpm higher, i didn't understand

hi, i installed my g4x and i'm happy with link, car is stock engine(impreza gc8 v6), when hot car is shaking on idle, my tuner set idle 1000rpm when fan is on, there is no shaking, but normal idle is shaking, i changed plugs and coil but didn't change anything and something about 3000rpm car is shaking too when car is at (no boost) i remembered this problem is also oem ecu i'm using can lambda, bosch iat, and stock v6 engine my tune and little log are here, https://drive.google.com/file/d/1G9TkT_JF3mnp6bVLKNh3YEoyN9rI49nk/view?usp=sharing https://drive.google.com/file/d/1IL4uX2pUgcxOB3XaTYa8QN3ZYw--ClH9/view?usp=sharing

i guess you can't mix trigger wheels,if you do not want to use avcs, you can convert v6 trigger setup, but if you want avcs you should use v10 trigger wheel

if you want, you can look my thread, sell it and buy can lambda

bit of an update, i installed can lambda and i didn't remove my old aem one, aem reads about .7-8 higher, when afr is about 14.7, aem is reading 15.7-8 i controlled spark plugs, probably aem is the wrong one

hi i installed my wrx6 g4x on my gc8, first i hooked up bosch iat no problem(an temp2), second bosch ntc sensor for oil temp(an temp3)(from oil plug) now i want to install bosch combined pressure temperature sensor but i don't need temperature from combined sensor if i hook up directly an volt5 for pressure will i be ok ? or do i have to connect temperature pin? if i need to confirm myself i 'll hook +5v, ground and an volt5 right ? Regards, Semih

i wonder did you use shielded cable for that wiring? or i wonder if it's helps? (same car here) if i were you i would redo whole ground wiring on that car

thanks for the clarification, i'll look wiring difference, when i look haltech wb1 manual it says connect lambda controller ground to battery ground, if i connect directly my can port, does this ground difference cause a problem or our can port ground same as battery ground? (i do not want to look my ecu with multimeter)

hi, i'm making can loom for lambda controller, my board is v1.4 wrx6x but can wiring is not listed, is this sequence right ? and for example if i use another brand lambda controller(for example haltech wb1), can i use same way like link can lambda(directly connect from can port)

i can not start new reply sorry for update old thread, i want to ask another question for example i want to connect haltech wb1 controller, can i connect like link can lambda? can i use 12v and ground directly from ecu can port ?

i can not write any message or thread some old threads

you're right guys, i wanted to keep as a spare(with new sensor) but i'll probably sell it

i bought this wideband about 2016 when my maf was failed

Thank you Adam, i guess my uego is last revised one, hope works correct

hi, i want to connect my aem wideband to my link g4x v6 impreza(i want to hook it temporarily until i get link can lambda kit) i'll use analog inputs that's ok but which cal table should i use ? if i use lineer cal tables will i be ok ? if ok, i'll enter 0v and 5v lambda regards, semih