Cnote0ne

The car is a 350z with a G4+ PnP. It started with a bad O2 sensor which I replaced now twice with new sensors and the car still idle rough and has no power. AN-10 O2 sig LF show 0.00 while the AN-11 O2 Sig RF show .85. https://1drv.ms/u/s!AjI8sO2lko8akH6kI96B56xIdXJM?e=lHk5VA Log file https://1drv.ms/u/s!AjI8sO2lko8akH921J_VdxL44Hy9?e=xgTCJj Base map

The stalling seem to stop. When I'm in neutral and still moving, it drops to idle and stays there. Thanks Adamw.

Speed lockout didn't help. It still wanted to stall, I had to blip the throttle to keep it from stalling. Thanks, I'll try your suggestion.

Ok, I'll try it with speed locklout off. Thanks.

I've been doing some fuel tuning and now the stalling is back. When I go into neutral from a 3k rpm rev the rpm drop and it stall. Logfile: https://1drv.ms/u/s!AjI8sO2lko8ajmtIeFfEtJ2aZ1Pw?e=KVsk54 $Basemap070720-AFR1.pclr

The car is idling much better and no more stalls. Much appreciated! Thanks.

Thanks, I'll try it as soon I get back home in a couple of days and report back.

Thanks, figured it out. Here is the link. https://1drv.ms/u/s!AjI8sO2lko8ajmgCcZOY36le9L5I?e=EhGtzU

Yes, I need an email address.

Hi All, My car is stalling when I stop at red lights. It's not all the time, usually if I coast in neutral. I searched the forum and found lots of stalling post but none of the solutions seem to work for me. Tech support can't figure it out either. They don't see any issue with e-throttle setup and tracking. Hope someone can help. Base map attached, but log file too large to upload. I can email it. Thanks. E-Thrttlworkingbasemap62620.pclr

Hi, My car is going into limp mode which restrict the RPM to 1800. I also get 2 fault codes 73 and 75. My base tune and log are below. Thanks. 62420basemap.pclr loadLog 2020-06-21 3;03;15 pm.llg

Problem solved! some how it stop getting power. I switch the power supply and now I get AFR/Lambda. I also found ground wire was a little loose, not sure if that contributed to the list of issues. I want to thank you guys for all the help. Thanks Richard!

The Lambda sensor is new and came with the Link CAN-Lambda module kit. It stays in calibration with no change. I will source a separate battery to test your suggestion. Thanks. LambdaCalbrLog 2020-06-22 12;54;12 pm.llg

Lambda 1 Status show disabled/diagnostics and Lambda 1 Error show Ok. Here is the log. Thanks CANLog 2020-06-22 11;43;54 am.llg

The power is from the ignition switch and it shows a solid 12.4 volt, ground is to the chassis.

Here is the map. Basemap1.1.pclr

You are correct sir, the wires were reversed. I swapped them around and it find the device now but still no Lambda1is displayed. I get all green prior to starting the engine, once I start the car the errors return. Log file below. Thanks. CAN1Log 2020-06-22 9;06;10 am.llg

Tried 500kb and that clear all of the errors but still no device is found. Here is my wiring diagram for the connector.

Correction...the COM issue was not related to the resistor. I resolve the COM issues but still no change with the resistor installed.

I added the resistor on the white and green wire at the connector to the wideband controller and COM stop working, couldn't connect to the ecu. I removed the resistor and it connect fine. I bought them just in case...but I read somewhere that they were not necessary if the correct cables/connectors were used.

No, I don't see it when I do a Find Devices. I'm using the CANPCB and CANF connectors so I was under the impression I didn't need a resistor. Here is a log I just pulled. Log 2020-06-21 12;18;16 pm.llg

Thanks Richard. When I select Link Can-Lambda and set it, I get these CAN 1 errors. I turned off AN volt 9 as you recommended. 62120basemap1.pclr

It's the Link Can-Lambda module for wideband. Here is my tune with Lambda 1 setup for AFR/Lambda. Thanks. 62120basemap.pclr

Here is the current tune and a log. Thanks. 350zVQ35deTwinT440injbuiltengAFRLambda.pclr Stableidlelog.llg

Ok, I'm getting MAP numbers now but no AFR/Lambda 1. I have the Link CAN-Lambda wideband controller on CAN 1...all green and ok in Runtime Values.