SC845
-
Posts
18 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Blogs
Posts posted by SC845
-
-
correct @DerekAE86. I am sure it connects to an aux but what setup parameters do i set for it to work as it should?
-
If someone has connected and configured the Air Control valve on a 4AGZE supercharger (see the pic), it will be great if you can share some advice on it... not sure how to configure it.
-
Thanks for the files Adam... please check the screen cap, i do not get the looging status or memory data on AIM. I've uploaded the link file you sent to the ECU and the AIM files as well into RaceStudio
-
Files attached... thanks for your help
-
Hi... how can I setup CAN on a MonsoonX to send the ECU logging memory use and status (because I will switch logging on off via switch) to a AIM strada dash. And how to setup the AIM dash to received those parameters?
-
@koracing thanks a lot for the base tune. Was helpful to get the car started. Will be sharing some logs in the coming weeks to update on the status of the engine and tune. Thanks again.
-
Its a map i used on a 3sge at some point... i've started reworking it for the 4agze but no done with it yet as we are completing some wiring jobs on the chassis/body before we can run the car. We eliminated the cold start injector on the 4agze. I will capture a log later tonight when we attempt another start, will send it to you.
-
Hi Adam, so we got the car started fine... haven't connected the idle solenoid yet, but it maintains idle fine. But as soon as we give it some gas engine shuts off. Can you go through the file to see if we are missing out on something... accel enrichment has been setup. Aslo if you can advise on the idle solenoid setup we have currently. Thanks
-
Thanks for the quick analysis... will make the arming threshold changes and review the fuel table and injector settings and then give it another go tomorrow. Can you have a look at the attached setup file, i've setup the supercharger clutch to actuate via AUX 3. Are the settings for it correct? Also how did you wire the air control valve located on the supercharger... see attached pic to know which valve i am talking about. Tazz-4AGZE-Rally-V07.pclx
-
Attached are new trigger scope logs... do you see any errors there? I shut off the injectors when capturing the log
TriggerScopeLog-07.llgx TriggerScopeLog-08.llgx TriggerScopeLog-09.llgx
-
Hi Adam... managed to start the engine but then it shuts down despite giving it some gas... and we have trigger errors. Attached is the trigger scope log and the pc link file. Can you give us some ideas as to why its not holding idle?
-
Hi... any chance you can update us on how to setup tigger 1 and 2 in PC LINK? Does the setup need to change if we use coil on plug?
-
Hi... after setting up CAN lambda several times, it is not giving any reading. It is a new unit. Attached is my log file, can someone assist?
-
Hi, does anyone have a basemap they can share for the a Toyota 3sge beams redtop. I know the altezza basemap is there already within the link software, but i just wanted to have a redtop specific basemap before i start my engine... of course I will need to reconfigure the ins and outs as per my wiring setup... thanks in advance to anyone who can help.
-
Hi Jose.... I am trying to have a base map for my redtop 3sge and specially for the VVT.
Do you think you can share your pclink file for your redtop with me? -
Hi... in the Altezza base map injector flow rates are set to 906cc/min... is that correct or do i need to change it as i think stock injectors on the altezza are 340cc/min.
-
Hey Davidv.... I am also running a 3SGE red top with stock ECU and moving up to a Link G4+ soon.... would be great if you could share some maps so I can get started
Wiring & config of air control valve on 4AGZE
in G4x
Posted
Thanks @essb00 & @DerekAE86 for your inputs, got it to work correctly... Hopefully it will help extend the supercharger's lifetime.