Hurtenstein
Members-
Posts
26 -
Joined
-
Last visited
Hurtenstein's Achievements
-
Had some R35 coil issues, but fired first time after that. Cheers again.
-
Hurtenstein started following Sharing Expansion 5V+ supply. , Decaying trigger scope. V5-6 Subaru. , WRX V5-6 AN Temp 4 stuck on 5V and 6 others
-
Nearly ready for a first start and checking over things, my trigger pattern is inconsitent. G4x plugin set to V5-6 pattern. The pattern is what I was expecting to see, 2,1 on the crank and 3,1,2,1 on the cam, but the peaks are all over the place. The noise on the trigger 2 between spikes is also concerning. What could be the cause? Secondly, should i be seeing these turn green when cranking? I get no errors. Thanks. Trigger Scope - uneven.llgx
-
Fixed with a wired in 1k on AN Volt 2. Thanks.
-
Spew. I thought there was 4 like my Xtreme and the manual had to be typo. It's all wired up and terminated. I planned to just figure out which was the double up once it was wired and I could see the values. Can I use a spare AN for IAT with a wired in pull-up resistor? Or does the ECU only look for IAT on the Temps? B136-1 (2 slots up) is a spare AN for me and I can just shift the pin.
-
My WRX6X has AN Temp 4 stuck on 5V. There is some confusion in the drawings as the quick start says Temp 3 is pin B136-19, but also says T3 is on the expansion loom. Ive used the expansion T3 for oil temp and get a change in readings when i plug/unplug so i'm presuming that the onboard Temp is actally Temp 4. B136-19 has no wire in the plug from factory, so i added one in. Even with my new wiring connected or not, I still get 5V on Temp 4. Any ideas?
-
Hurtenstein reacted to a post in a topic: R35 GTR
-
https://dealers.linkecu.com/G4X-FuryX https://dealers.linkecu.com/LINK-MXG-Strada-7-Dash-Street-Edition https://dealers.linkecu.com/2LA_ https://dealers.linkecu.com/2LB_ https://dealers.linkecu.com/LSU49_2 https://dealers.linkecu.com/MAP-Sensor-MAP4 https://dealers.linkecu.com/3BCS
-
Perfect, will do. Thanks.
-
Hurtenstein reacted to a post in a topic: Audi 4.2 V8 VVT control
-
The old 40V were just VVT on the intake. I was trying to nut out the Audi drawings and wasn't sure. I can't find any input that refers to "Cam trigger", but there are two called "cam position" as shown below. I was thinking that the "cam position" would just be for the ECU to know advance/retard position, but does it also use it as a trigger?
-
When using a single output I meant. To avoid having to use 2.
-
Hurtenstein reacted to a post in a topic: mounting bolt size
-
Can you set a PWM channel to ramp up like a soft starter?
-
Thanks. I thought that would be the case.
-
If my G4X Xtreme is supplied (A5) power via an ADIO of the PDM, can the +5 and 0V PDM pins be used in conjunction with a DI/ANV on the Xtreme? Or do I need to use the Xtreme +5/0 pins?
-
Mint, thanks.
-
Are all of the +5V supplies on the expansion slots common to the main header output also? (B136-12) on WRX5-6 in this case? Example is the E-throttle. The expansion slot gives 3x ANvolts, implying that 2 are for the APP and the third is the second TPS, in addition to the existing TPS. The existing TPS gets its +5V from main header B136-12, can I use this same supply for the new TPS, even though the ANVolt signal will be going back to the E-throt expansion. Or I do a take a +5V from that expansion slot out to the new TPS also?
-
Vaughan reacted to a post in a topic: CAN interface between G4+ and G4X
-
Cheers. I'll probably end up leaving the existing WB on the JST5 and use CAN2 for everything else.