AEWON Posted April 21, 2020 Report Share Posted April 21, 2020 Hi guys, I have tried multiple files and configurations to get my C125 to be found on the Link Canbus detection with no luck, it can see my CAN lambda, ive tried the help file in the link software for Motec dash, changed settings to suit, could someone have a look at the current setting in my map and config file and see where I might be going wrong? Other thing to note: Im using canbus 1 on G4 and plugging into the ECU connector on the C125 which Is CANBUS 2, but have tried swapping everything over but did not seem to change. Cheers! NISSAN S14.pclr 59ebc9cd58ff0_LINKG4_MoTeCC125DASHETC (2).CC8 Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 21, 2020 Report Share Posted April 21, 2020 The "Find devices" tab is only for programming Link CAN Lambda's. It will not discover any 3rd party devices. Your config looks ok. Are you getting no live data on the dash? There arent any CAN errors showing in the ECU file. Is the CAN lambda working? What do the diagnostics in the dash show? Quote Link to comment Share on other sites More sharing options...
AEWON Posted April 21, 2020 Author Report Share Posted April 21, 2020 Thanks for taking a look and clarifying about the find devices! Just figured it was the same process for every device. No data at all on the dash, CAN lambda is being discovered by the Link ECU but no voltage seems to be being displayed in ECU real time, I take it this is because the engine isn’t running? I cannot run the engine at the moment (fresh engine) . I’ve checked for power and earth at the CANLambda and it is all OK, so I can only assume that since the ECU discovers the Lambda sensor the CANbus must be Ok? Can’t seem to find any dash diagnostics to be honest, literally pulled it out of the box yesterday, have a feeling it’s something in the Dash I’m missing. Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 21, 2020 Report Share Posted April 21, 2020 can you attach the actual dash config, not just the CAN template. Quote Link to comment Share on other sites More sharing options...
AEWON Posted April 21, 2020 Author Report Share Posted April 21, 2020 Adam, ive edited my response.. but will send dash config file ASAP LINKG4+TO_C125.json Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 22, 2020 Report Share Posted April 22, 2020 Note that is not a dash config you've attached, it should have an extension something like .c125v61 Quote Link to comment Share on other sites More sharing options...
AEWON Posted April 22, 2020 Author Report Share Posted April 22, 2020 All good, I’ll try and work my way through it and find the file Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 22, 2020 Report Share Posted April 22, 2020 Its actually not that intuitive, you've got to go to >file>open, then in the open dialog box select your config and click export. Quote Link to comment Share on other sites More sharing options...
AEWON Posted April 23, 2020 Author Report Share Posted April 23, 2020 Worked it out, so in the motec dash manager the template I got from these forums had defaulted to CAN1 of the motec, had set the link ecu up on CAN1, but the Motec track loom ECU connection is CAN2, swapped the template into CAN2 in the motec dash manager and now I can see some Live data on the Dash. In hindsight, wish I had gone down the AIM dash route, Motec is quite full on Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 23, 2020 Report Share Posted April 23, 2020 You'll get used to it. Obviously with more flexibility comes more complication, but they are great dashes. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.