Wastgate323 Posted November 21, 2021 Report Share Posted November 21, 2021 Hello I'm new to LINK ECU. Before i only use MS ECU's. But for my new Project (RX8 Track Car) i use a more professional ECU. I have read alot about the CAN Protocol from the RX8 here in the forum. The Dashboard has right now only ABS ans EPS error codes. The rest has a Signal from the ECU (Engine, Coolant, Oil, Battery) I have use the information from Adamw MAP. i try to test the ECT. but the Gauge does not work. (I use a Fury X ECU) I had simulate a temperature above 95 degrees. But no reaction. Thank you for your efforts Quote Link to comment Share on other sites More sharing options...
Adamw Posted November 21, 2021 Report Share Posted November 21, 2021 Attach your tune and I will take a look. Much of the CAN scaling and enumerations has changed from G4+, so it will likely need some changes to work in G4X. Quote Link to comment Share on other sites More sharing options...
Wastgate323 Posted April 9, 2022 Author Report Share Posted April 9, 2022 I'm finally back in the workshop. i have all wired up. Power Steering and ABS without DSC. Any device has Power supply. but the controllight are still on. (ABS, Handbrake and EPS) Thank you for your help. kind regards Lukas rx20b.pclx Quote Link to comment Share on other sites More sharing options...
Wastgate323 Posted April 10, 2022 Author Report Share Posted April 10, 2022 I have also a problem with wheel speed sensors. I can not add parameters lf, rf, lr and rr wheelspeed that receive to ecu. Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 10, 2022 Report Share Posted April 10, 2022 Update your firmware, then load this map. The CAN Aux labels on stream 3 arent displaying correctly in this one but I think it will with current firmware. rx20b v1.1.pclx Quote Link to comment Share on other sites More sharing options...
Wastgate323 Posted July 18, 2022 Author Report Share Posted July 18, 2022 Thank you so much Adamw. The Engine is finally run and the Cluster and EPS works. ABS llight is also off, but i can't test it right now if it really works Quote Link to comment Share on other sites More sharing options...
Wastgate323 Posted July 2, 2023 Author Report Share Posted July 2, 2023 The Car was finally on the Dyno. Everything works betwenn the ECU and Cluster. But the Speed dosen`t work. I have change the ABS Unit from Europe Spec (Bosch) to a US Spec (Sumitomo) without DSC. The ABS light works correctly, i think. If i disconnected one Sensor the light goes on. if all sensor connected, the light goes off. Is something in my Canbus Stream wrong? RX8fertig-geändert.pclx Quote Link to comment Share on other sites More sharing options...
Adamw Posted July 2, 2023 Report Share Posted July 2, 2023 Your user stream 2 is sending out "Driven wheel speed", but you have no driven wheel speed source assigned in your chassis and body settings. Set this to average front speed or similar. Quote Link to comment Share on other sites More sharing options...
Wastgate323 Posted July 9, 2023 Author Report Share Posted July 9, 2023 Thank you Adam. I try it, but it dosen't work. Should i try without Signal from the ECU? I'm not sure, but the ABS Unit read all 4 Wheelspeed sensors, and send this Information to the CAN-Bus. So the Gauge Cluster can read this Information directly from the ABS Unit? Thank you Quote Link to comment Share on other sites More sharing options...
Adamw Posted July 9, 2023 Report Share Posted July 9, 2023 The cluster gets its speed from the ecu, not the abs. Is driven wheel speed reading correctly in the ecu software now? Can you attach your most recent tune. Quote Link to comment Share on other sites More sharing options...
Wastgate323 Posted July 18, 2023 Author Report Share Posted July 18, 2023 Hello Adam Yes i see 50-60Hz on the rear Wheel Speed in the ECU. But the Cluster dosen't work. (at the moment i only can test on the Car lift, so the front wheels aren't turn. So i set the driven wheel speed to "average rear speed" rx8.pclx Quote Link to comment Share on other sites More sharing options...
Adamw Posted July 18, 2023 Report Share Posted July 18, 2023 Speed should be in byte 4 & 5, you have it in byte 2&3. Change the start position to 32. Quote Link to comment Share on other sites More sharing options...
Wastgate323 Posted July 19, 2023 Author Report Share Posted July 19, 2023 Thank you, now it works Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.