tao Posted September 8, 2015 Report Share Posted September 8, 2015 Helpwiring link atom to honda obd1.I want pin out link atom to pin obd1 thank you Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted September 8, 2015 Report Share Posted September 8, 2015 Hi tao.What model Honda do you have ?Are you sure you have OBD 1 ?Only OBD 2 Protocol is supported.If you have OBD2 then all the information is in the HELP files on how to wire it up and your software settings.RegardsDave. Quote Link to comment Share on other sites More sharing options...
Simon Posted September 8, 2015 Report Share Posted September 8, 2015 (edited) Hi DaveI think what he is after.Is how to wire his atom in to a early Honda loom / plugi.e A pinout of the Honda with connections to the atom listed. This is not something that we have. Edited September 8, 2015 by Simon Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted September 8, 2015 Report Share Posted September 8, 2015 Hi Simon,glad your on the job, ha ha.I totally got that wrong.Joys of being on the FORUM at 2:50 am.RegardsDave. Quote Link to comment Share on other sites More sharing options...
tao Posted September 10, 2015 Author Report Share Posted September 10, 2015 Hi Simon and Davethank Simon , DaveYes i need "i.e A pinout of the Honda with connections to the atom listed." Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted September 10, 2015 Report Share Posted September 10, 2015 Hi tao,if you can supply a ECU pin out schematic (IN ENGLISH) for your car then I can help give you the information to cross wire to the ATOM.RegardsDave. Quote Link to comment Share on other sites More sharing options...
tao Posted September 12, 2015 Author Report Share Posted September 12, 2015 Hi Dave Ok Pin out my ECU imagethank you Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted September 12, 2015 Report Share Posted September 12, 2015 Hi Tao,the picture is too small and when I save it and open and enlarge it is heavily pixelated, I can't read it sorry.Also is there a connector C.RegardsDave. Quote Link to comment Share on other sites More sharing options...
tao Posted September 13, 2015 Author Report Share Posted September 13, 2015 Hi Dave My Ecu honda obd1 no connector CI hope you will support menew image Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted September 13, 2015 Report Share Posted September 13, 2015 Hi tao,that is much better.Thank you, I will be able to help out now.Can you also list what outputs you wish to use.What inputs do you wish to use.If you do have a LINK G4+ ATOM there is no onboard MAP sensor so an external unit will be required if you want MAP.The ATOM is limited with INPUTS and OUTPUTS.RegardsDave. Quote Link to comment Share on other sites More sharing options...
tao Posted September 15, 2015 Author Report Share Posted September 15, 2015 (edited) Hi DaveWhat I wantA1 = injecteur 1A2 = injecteur 4A3 = injecteur 2A4 = Vtec SolrnoidA5 = injecteur 3A7= Main RelayA8= Main RelayA9=idle air control valveA13=check engineA15=A/C clutch relay A21=ignition unit signal (RPM signal)A22= ignition unit (RPM)A23=main relay groung A24=groundA25=main relay (IGN) A26=MultigroundB1= main relay (IGN)B2=MultigroundB5=A/C switchB8=P/S Oil Pressure Switch B9=main relayB10=Vehicule Speed sensorB11=CLY 1PB12=BYL 1nB13=Top Dead center PB14= Top Dead center MB15=Crank Position sensor PB16=Crank Position sensor ND6=Vtec Pressure switch D16=Throttle Position sensorD13=Coolant Temperature SensorD17=Map SensorD19=map sensor V+ D20= Throttle Position sensor V+D21=map sensor groundD22=Ground Thank You Edited September 15, 2015 by tao Quote Link to comment Share on other sites More sharing options...
Dave Kriedeman Posted September 16, 2015 Report Share Posted September 16, 2015 Hi Tao,Please find attached below stage one of the wiring diagram for you.I will try to finish the rest today, but I am unwell so I will see how I go.RegardsDave. Quote Link to comment Share on other sites More sharing options...
tao Posted September 17, 2015 Author Report Share Posted September 17, 2015 Hi DaveThank you very much and I will wait for the rest. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.