Jump to content
dobsondynotune

Re: BASE MAPS

Recommended Posts

HELLO EVERY ONE MY NAME IS ROSS HONNOR  I OWN AND OPERATE DOBSONS DYNO TUNING IN NEW ZEALAND,           I THOUGHT I WOULD START THIS LINK  TO HELP THOSE OF YOU THAT ARE A BIT LOST AND WOULD LIKE A BASE MAP TO HELP WITH SETTING UP. THE MAPS PUT ON HERE ARE SOME OF THE CARS WE HAVE TUNED I TAKE NO RESPONSABLITY FOR YOU BLOWING UP YOUR CAR BECAUSE YOU HAVE DONE SOMETHING WRONG OR NOT HAD IT TUNED CORRECTLY. THESE MAPS ARE INTENDED TO HELP YOU. PLEASE DONT PICK THEM TO PIECES AND ABUSE ME IF YOU FIND IVE MADE A MISTAKE. AS IM PROBLERLY LARGER THAN YOU.  YOU ARE MORE THAN WELCOME TO RING ME OR EMAIL ME ABOUT YOUR SET UP I WILL ONLY CHARGE YOU IF YOU KEEP RINGING  MY WORK HOURS ARE 8AM TILL 5PM  NEW ZEALAND TIME PLEASE DONT RING ME OUT SIDE OF THIS TIME WITH OUT ARRANGING IT WITH ME FIRST.

MY MOBILE NUMBER IS 0064 21 754832 FOR INTERNATIONAL CALLS

ph 021754832 for new  zealand customers

or my workshop email is: mrdynotune@gmail.com

  WEB SITE: face book  Dobsons Dyno Tuning

    

Edited by dobsondynotune
updating contat details

Share this post


Link to post
Share on other sites

Hello erveryone,

I´m lloking for a kind of base map for my new setup.

Want to test if everything runs fine before it goes to the mapper.

As he is not from my country, it would be very bad if I have a oil leak or something like this.

Setup:

RB26dett - arp headstuds - tomei metal headgasket

2x garrett 2860-5 turbos

2x bosch 044 fuel pumps

1200cc lucas delphi 2.2ohm resistors (resistorpack solderd in)

Internal map sensor connected - no AFMs

I´m running e85 (ethanol)! not super98

Share this post


Link to post
Share on other sites

Hi Ross.

I am a french owner of '04 WRX with hard modifications :

EJ25 (STi v10) with Eagle connecting rods, Mahle Pistons, Cosworth engine bearings, Cometic Phuzion head gaskets

STI v11 heads (dual AVCS)

Reversed intake manifold (Magnus) (cable throttle, not by wire)

Dynamics Injectors (1000c)

Perrin fuel rails

Sard fuel pressure regulator

Anti-surge fuel system (Bosh pump 300l/h)

Twinscroll header (Prodrive OEM)

SC46 twinscroll turbo

Mishimoto aluminium radiator

Gearbox oil radiator

Power steering oil radiator

Rear differential oil radiator (Perrin)

STi v10 DCCD gearbox (manual control)

Toyota 2JZ twin turbo FMIC (TRD)

No A/C, no ABS, no ESP

I just bought a G4 Xtreme in order to control quad AVCS and many other things.


I am looking for a base map for this car (SP98, not E85 for the moment). I don't have SI-drive or E-throttle and I don't want the MAF any more (MAP + IAT= is the best!)

Do you think I will have to install basic camshaft position sensor (with this braket :

http://www.carmodsaustralia.com.au/ecommerce/products/171/cosworth-billet-cam-angle-s=
ensor-bracket-sb0002-171-1005-lrg.jpg

http://carmodsaustralia.com.au/ecommerce/products/171/cosworth-billet-cam-angle-s=ensor-bracket-sb0002-171-1005-lrg.jpg' target='_blank'>for first start?
(my STi v10 heads don't have OEM place to fit the sensor)

Best regards.

Jim

Share this post


Link to post
Share on other sites

Hi, needing a base map for 1993 Crown Vic 4.6L OHC V8. Had it running (badly though), updated ECU from 4.3 to latest 4.9.8 now appear to have no spark. Can send previously working base map if needed.

Cheers, Sam

Share this post


Link to post
Share on other sites

Hi All,

I just fitted Ver10 quad avcs Sti engine, and running on Link G4 Extreme ecu.

Anyone has the base map for the above engine, which I can load into the G4 Extreme and have some sort of reference point to tune from there?  Especially the ignition timing, avcs settings... 

Thx

 

Share this post


Link to post
Share on other sites

Hi,

i am sory for the kind of the question.

When i am tying to open files from maps,it openes them with preset programm.

By my mistake i changed how to open the files.I have preset my laptop to explorer ,then word and then excel...trying to remember which was the preset one.

If i open my files when i have opened the demo program,then i can read them.But i cannot read as example what you have in your base maps.

Please help me a little

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×