Dynotech NZ
Members-
Posts
35 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Blogs
Downloads
Everything posted by Dynotech NZ
-
Inshan  Post you .pcl file, ill look at it and see what your tuner has done and show you the avcs looks like on a 2002 jdm sti I tunedon our dynapack dyno last week.  Dynotech Industries
-
Post your pcl file
-
Got to your fuel table Right click the load axis Select axis setup Under Y axis select 'TPS main' Push init axis button Push Apply button Done
-
Hi Ross do you have a good base/starter map for R33 G4 plugin RB25det
-
What firmware are you running? Try upgrading to the latest, as it works fine for me 4.8.5  Send me your map [email protected] and Ill take a quick look for you  Phil
-
Same as the Bosch mate. Â However I would highly recommend fitting a new Link item to the intercooler pipe just before the throttle body. The std 1 in the inlet manifold will suffer from heat soak!! I have tried and tested this on my own Evo 9. Â Phil
-
7v=2.36 Â 9=1.320 Â 10v =1.17 Â 11v=0.95 Â 12v=0.8 Â Â 13v=0.67 Â Â 14v=0.56 Â Â 15v=0.46 Â Hope that helps
-
I can confirm i have the same problem with latest 4.8.1.1033 Â Phil
-
Have you carried out a MAP/BAP calibration?
-
first link ever made (gts link ) map sensor question
Dynotech NZ replied to claudiumxg's topic in Link G1
Just buy the link 3 port soleniod and wire to the active soleniod wiring (not the passive) Â Done this on my Evo 9, works perfect and I use close loop boost for accurate boost control -
Gear calc can be calibrated from speed DI input
-
3 or 4 plug ecu mate?
-
Thanks Ashley Yeah i noticed that table, it is labelled as table 8 and all values were half my target as you say Keep up the good work!! Phil
-
And here is screen shot with firmware 4.8.0 Thanks Phil
-
Hi team Just updated firmware from 4.8.0 to 4.8.1 (Evo 9 plugin G4) Went through settings to double check everything and boost target table is now missing! (I have attached screen shot below) Keep up the good work, Thanks Phil
-
^^^ + 1 If he still wants to lock it he obviously has something to hide If thats the case I would chose another tuner
-
You must tune with IAT corrections enabled!! The std IAT settings work well in most cases
-
Log Parameter Scaling Keeps Reverting Back to Original Values
Dynotech NZ replied to Josh Burt's topic in Link G4
Load up you map into PC Link, press Ctrl E The set up Ecu parameters box opens, set parameters to your desired figures. Save Should be good to go Phil -
Hi guys. Does any one have a base map for a 1jz non vvti. Car is Std but with gt35/40 single turbo. Any help is appreciated. Please email to [email protected]
-
G4 Evo 9 plugin on board data logging question
Dynotech NZ replied to Dynotech NZ's topic in Link G4
In Pc link help it says 100 parameters are logged (roughly) I see only 59 in my parameter list -
Hi guys How do i add more parameters to log via internal logging? I want to log items like WGDC IAT fuel corrections IAT ignition corrections Antilag fuel Antilag ingnition ETC ETC Is it limited to just the items listed as you can choose when logging via laptop fine Phil
-
use the search feature mate, it literally took me 2 seconds to find it http://www.linkecu.com/support/documentation/technical-drawings/S04/view?searchterm=evo+afm+wiri
-
Off, i will get 1 now with it on
-
Hi Cameron With the over run fuel cut turned on, i still experience the bucking at around 2000 - 1500 rpm on the over run. Over run fuel cut is set at 1600 rpm on warm engine Any ideas? It is going on a hub dyno tomorrow for fine tuning of the timing and afr's. But tuner isnt sure he will have time to look at this issue on the road after (he is very busy and doing me a favor getting me in tomorrow) Attached my map