Jump to content

efi265

Members
 View Profile  See their activity

  • Posts

    113

  • Joined

  • Last visited

 Content Type 

Posts posted by efi265

  2. g4x gttx map senor issue

    in G4x

    Posted

    hi we have wired map sensor to anv1 thru the maf sensor.issue we have is it fires and runs then cuts out ,we also cant calibrate it reads either 3.8 kpa and about 97mgp  .so then we wired to the expansion v5 then we still couldn't calibrate it then the map says 204kpa not 3ish kpa and mgp drops to 45 ish so half .we have tried a few things sorry

    https://1drv.ms/u/s!AsueBbAiWzmW1y1vCqz5dOcQ-1C4?e=FcfGak

    https://1drv.ms/u/s!AsueBbAiWzmW1y5TbpYv-OQgHpsJ?e=grfBjB

     

    thanks

    its an innovate 4bar map sensor so i

    dont no if thats the issue

  6. my afrs have started going crazy

    in G4+

    Posted

    Hi Adam thanks for your time to reply ,i appreciate it. so i have had a look at previous logs and  all my other fp readings are 296+ kpa or 43 ish psi which is what my base pressure setting should be from memory .so ill check pumps and reg and filter hopefully work it out and let you no .

    I run the AEM's Wideband UEGO  gauge setup thru my link,

    cheers Ross

    attached is an old log showing no less than 41.5 psi https://1drv.ms/u/s!AsueBbAiWzmW1yBgBiIoXtBqxhrH?e=M3KaGE

  7. my afrs have started going crazy

    in G4+

    Posted

    Hi guys my afrs have been all over the place .I have just removed the manifolds as i had an leak start recently i could hear .all seems good now but my afr's are still rubbish going over 22 when throttle pressed and then can go down to 8 on decleration ?need some help.i have done a re-calibration on my map sensor but not sure its been a while cheers

    attached is my log file some help be greatly appreciated thanks

    https://1drv.ms/u/s!AsueBbAiWzmW1x5R9Nbr2v2w4rTX?e=HLqFNV

     

     

  13. Pc link new layouts not saving

    in G4+

    Posted

    Hi so have loaded the new layouts which are excellent but I cant seem to make them save .I load them open my tune save and everyone it reverts back to old gayness .the tune is saved as startup tune ,i save the layout ,,do I use this file heading forward?  Thanks

  14. Probably a dead horse aem uego wideband

    in G4+

    Posted

    Hi trying to set this up read a few posts not great

    I have a g4+ extreme and the gauge is wired to anv6 and in the menu has a setup for aem uego but doesn't seem to work. Sure I have it set to the innovate option at the moment .can I select the uego option and will it read properly or is it dog food wrappers and in the bin waste of time if its wrong 

    Thanks Ross 

  16. trying to setup afr logging on my new g4+

    in G4+

    Posted

    hi im trying to setup logging on my new g4+ setup for tuning afr's and cant find how to get afr readings .my g4 has it as wideband .i see lambda 1 and anv6 lambda ,i want tps,,map and engine speed how can i do this! also when i look at my fuel and ignition maps it has an option to view as a table .once again in the g4 software i have a table and the conventional map but again i havnt figured out how this is done .thanks

    https://1drv.ms/u/s!AsueBbAiWzmW1TxrDmM2AzueA-ZN?e=zL2A15

  17. new setup and no trigger signal

    in G4+

    Posted

    Sorry one more question .do I set trigger priority to trigger 2  or 1 i just read another forum trigger setup post and it showed as priority to trigger 2 , 36-1 crank trigger hall sensor and modified dizzy with reluctor .cheers Ross 

  23. new setup and no trigger signal

    in G4+

    Posted

    hi i am setting up my new wire in g4+ extreme and cant get a trigger signal status in runtime or rpm signal ,also have run a trigger scope but dont no much about it tried a few things  still the same ran some trigger scopes and have logs .not much on trigger 2 .have a 36-1trigger wheel and modified singe pickup distributor ,haha cant tune it if i cant get it too run .engine is a fuel injected turbo hemi 265 in my old valiant .cheers Ross

    Charger start tune.pclr

  24. idle always different

    in Link G4

    Posted

    have been chasing an idle issue seems every time i get it setup .next start it wont idle again just seen an

    e throttle active table  table 1

    yet its not active or switched on thought perhaps thats the problem ?  i have switched off. idle ignition control ,closed loop lambda control ,closed loop idle control,and get it idling all good in open control  then re introduce all the close loop and it all runs good then after restart it wont idle again .is the  e throttle active table  table 1 meant to be green in the e throttle  run time menu ?

    cant upload the pcl to large

×
×
  • Create New...