George GEP Posted June 25, 2020 Report Share Posted June 25, 2020 i have got new Storm x, migrating tune from old Storm. i selected parameters one by one probably nothing missing but strange issue is that nothing works, no input no output no reaction on ecu side. in run time values i see no reaction from TPS, MAP etc wiring is there something different in X than in older ecus? is pinout different on X? Quote Link to comment Share on other sites More sharing options...
Vaughan Posted June 25, 2020 Report Share Posted June 25, 2020 attach a copy of your new and old basemap please and I'll see if I can spot what's wrong Quote Link to comment Share on other sites More sharing options...
Adamw Posted June 25, 2020 Report Share Posted June 25, 2020 It sounds almost like PC Link has locked up? Is the little refresh rate "frequency" at the top right of the screen bouncing around like it is live? Quote Link to comment Share on other sites More sharing options...
George GEP Posted June 26, 2020 Author Report Share Posted June 26, 2020 here are both files on this forum i can not attache more than 0.01MB file so i uploaded it to wetransfer. https://wetransfer.com/downloads/c186ef3a2db173865847d11418d60cc620200626060754/20466762d31dfe4024aec78dfdba67c620200626060807/6a9a40 please check and tell me what am i missing Quote Link to comment Share on other sites More sharing options...
Adamw Posted June 26, 2020 Report Share Posted June 26, 2020 Start by updating the firmware. You are on the first release so a lot has changed since then. Then can you attach a copy of tune again, saved after the firmware update. Quote Link to comment Share on other sites More sharing options...
George GEP Posted June 26, 2020 Author Report Share Posted June 26, 2020 ok will try now. and report. have u checked files that i posted? Quote Link to comment Share on other sites More sharing options...
George GEP Posted June 26, 2020 Author Report Share Posted June 26, 2020 updated firmware. still same nothing changed Quote Link to comment Share on other sites More sharing options...
TechDave Posted June 26, 2020 Report Share Posted June 26, 2020 Hi George As per my email yesterday, your basemap is working fine on the bench. Quote Link to comment Share on other sites More sharing options...
George GEP Posted June 26, 2020 Author Report Share Posted June 26, 2020 what a dumb forum i can not post small screenshot why is it limited so much in size? 10kb? seriously? :)) anyways i have all sensors disconnected and i see 4.02V in analog inputs on ANv2 and i see 3.3 / 3.8 Volts on TEMP1 TEMP2 when everything is disconnected OR connected. nothing is changing and none of other parameters react such as MAP, trigger or something. 5volt out from ecu does weird thing, sometimes it gives ot 5v sometimes 10v sometimes 2v. is that normal? Quote Link to comment Share on other sites More sharing options...
Adamw Posted June 26, 2020 Report Share Posted June 26, 2020 55 minutes ago, Adamw said: Then can you attach a copy of tune again, saved after the firmware update. Can you attach the new file please. There were some weird voltages reported in that last tune, I want to see if those have changed. Quote Link to comment Share on other sites More sharing options...
George GEP Posted June 26, 2020 Author Report Share Posted June 26, 2020 2 minutes ago, TechDave said: Hi George As per my email yesterday, your basemap is working fine on the bench. i can give you Team viewer access to laptop to check yourself what a weird stuff is going on. https://we.tl/t-JkmLHVqs6x new file Quote Link to comment Share on other sites More sharing options...
Adamw Posted June 26, 2020 Report Share Posted June 26, 2020 1 minute ago, George GEP said: why is it limited so much in size? 10kb? seriously? :)) We give each member a decent allowance, you have used your allowance up in other posts. You can use google drive or onedrive or a picture host to share files and pictures Quote Link to comment Share on other sites More sharing options...
George GEP Posted June 26, 2020 Author Report Share Posted June 26, 2020 3 minutes ago, Adamw said: Can you attach the new file please. There were some weird voltages reported in that last tune, I want to see if those have changed. https://we.tl/t-JkmLHVqs6x nothing changed Quote Link to comment Share on other sites More sharing options...
Adamw Posted June 26, 2020 Report Share Posted June 26, 2020 Can you remove from car and power it up on the bench with only 12V connected to Pin A5 and Gnd connected to A34. Quote Link to comment Share on other sites More sharing options...
George GEP Posted June 26, 2020 Author Report Share Posted June 26, 2020 3 minutes ago, Adamw said: Can you remove from car and power it up on the bench with only 12V connected to Pin A5 and Gnd connected to A34. will do, and? what to look for did bench 12v and gnd on table https://wetransfer.com/downloads/8718f918f45cfada2ed162576a0475c920200626082405/e5bd64f5b7ac99013250cea2aacc75ee20200626082420/7d0101 here is file and log 14 minutes ago, Adamw said: Can you remove from car and power it up on the bench with only 12V connected to Pin A5 and Gnd connected to A34. did bench 12v and gnd on table https://wetransfer.com/downloads/8718f918f45cfada2ed162576a0475c920200626082405/e5bd64f5b7ac99013250cea2aacc75ee20200626082420/7d0101 here is file and log Quote Link to comment Share on other sites More sharing options...
Adamw Posted June 26, 2020 Report Share Posted June 26, 2020 Ok, in that latest map, all your errors have gone away, None of the aux outputs are in fault, The AN Volt channels are all reading zero and the temps are all reading 5V (pulled up). So if it all works correctly on the bench, but everything turns to crap when connected to the car then it suggests there is a wiring problem in the car somewhere. Quote Link to comment Share on other sites More sharing options...
George GEP Posted June 26, 2020 Author Report Share Posted June 26, 2020 7 minutes ago, Adamw said: Ok, in that latest map, all your errors have gone away, None of the aux outputs are in fault, The AN Volt channels are all reading zero and the temps are all reading 5V (pulled up). So if it all works correctly on the bench, but everything turns to crap when connected to the car then it suggests there is a wiring problem in the car somewhere. investigating wiring side now, thanks will report Quote Link to comment Share on other sites More sharing options...
George GEP Posted June 26, 2020 Author Report Share Posted June 26, 2020 Aux4 goes to fault as soon as im trying to activate it or test it does not matter what function will i add to it it says fault immediately as soon as im trying to activate. i removed pin completely from aux4 and tried.. still fault other aux pins work fine what to look for? Quote Link to comment Share on other sites More sharing options...
George GEP Posted June 26, 2020 Author Report Share Posted June 26, 2020 here is triggerscope please check LS engine with VVT it looks like L99 engine. is triggerscope and settings correct? triggerscope log1.llgx here is Map and triggerscope link together https://we.tl/t-HF3ozH2bZB Quote Link to comment Share on other sites More sharing options...
Adamw Posted June 26, 2020 Report Share Posted June 26, 2020 11 hours ago, George GEP said: Aux4 goes to fault as soon as im trying to activate it or test it does not matter what function will i add to it it says fault immediately as soon as im trying to activate. i removed pin completely from aux4 and tried.. still fault other aux pins work fine what to look for? What wiring problem did you find? Was it related to aux 4? It sounds like possibly aux 4 is fried? They are over current protected so usually the only way you can damage them is by feeding 12V directly in to one when the output is activated. Quote Link to comment Share on other sites More sharing options...
George GEP Posted June 29, 2020 Author Report Share Posted June 29, 2020 On 6/27/2020 at 2:24 AM, Adamw said: What wiring problem did you find? Was it related to aux 4? It sounds like possibly aux 4 is fried? They are over current protected so usually the only way you can damage them is by feeding 12V directly in to one when the output is activated. wiring issue was that main 4 ground pins were attached to painted surface on a car where ecu was not getting ground so ecu was powered up from somewhere else but nothing worked also fuel pump which was on Aux4 wired through relay was not connected to ecu as well. not sure was it fed from trigger wheels or somewhere else. but once ground wires attached properly ecu started working fine but issue with failing Aux4 status. any thoughts? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.