Jacky Fung Posted July 15, 2020 Report Share Posted July 15, 2020 Dear All, I was setup a G4+ w/ Link MSX Strada before. It works fine. Now I'm switching to Monsoon G4x. Some of them are work fine. but I cannot get some of the reading like Oil Pressure, Fuel Pressure, Speed etc. I already upgrade the firmware of both but still no luck... here is my can setting of both. Would you help to found out what's wrong of setting? Thanks in advance. Jacky Quote Link to comment Share on other sites More sharing options...
Adamw Posted July 15, 2020 Report Share Posted July 15, 2020 Is it a MXS or a link branded MXS 1.2? The current Link CAN_BUS_BASE_LCC ECU stream in the AIM software is version V02.00.06, so the version .02 you are showing above is quite old. You have to click the "change ECU" button and reselect the new stream version. Quote Link to comment Share on other sites More sharing options...
Jacky Fung Posted July 16, 2020 Author Report Share Posted July 16, 2020 it's Link Branded MXS 1.2 OK. let me check the software version and get back to you. Thanks. Quote Link to comment Share on other sites More sharing options...
Jacky Fung Posted July 17, 2020 Author Report Share Posted July 17, 2020 Hi there~~ I checked I'm using V02.00.06 in MXS. Some parameter works like RPM, ECT, MAP, etc. But the Speed, Fuel Pressure, Oil Pressure don't.... Do you have any advice for that? Thanks. Quote Link to comment Share on other sites More sharing options...
Adamw Posted July 17, 2020 Report Share Posted July 17, 2020 Can you attach the map from your ecu and a short log of it driving. Quote Link to comment Share on other sites More sharing options...
Jacky Fung Posted July 21, 2020 Author Report Share Posted July 21, 2020 Dear Adamw, Attached w/ the map w/ the log. Thx for your help! Jacky Log.llgx Monsoon CIvic Base Map.pclx Quote Link to comment Share on other sites More sharing options...
Adamw Posted July 21, 2020 Report Share Posted July 21, 2020 Well you dont have speed, fuel or oil pressure working in your ecu either... This is because you dont have any wheel speeds assigned in your map, and your oil and fuel pressure calibration table is just zero. If you tell me what oil and fuel pressure sensors you have I will set it up for you. Quote Link to comment Share on other sites More sharing options...
Adamw Posted July 21, 2020 Report Share Posted July 21, 2020 Well you dont have speed, fuel or oil pressure working in your ecu either... This is because you dont have any wheel speeds assigned in your map, and your oil and fuel pressure calibration table is just zero. If you tell me what oil and fuel pressure sensors you have I will set it up for you. Quote Link to comment Share on other sites More sharing options...
Jacky Fung Posted July 22, 2020 Author Report Share Posted July 22, 2020 Morning Adamw, I review the map and found that I was selecting a wrong cal table. I didn't aware there are separate cal table between Cal and Linear Cal table. I think I can fix for pressure. Thanks. For speed, would you advice how to assign the wheel speed to the map? since I can get the correct speed on GP speed1, but not in LF wheel speed. Thanks for your kindly help!! Jacky Quote Link to comment Share on other sites More sharing options...
Adamw Posted July 22, 2020 Report Share Posted July 22, 2020 Turn off the GP Speed 1 input. Go to the chassis and body menu and set up like below. Also, your pressure calibration still looks wrong. 150Kpa isnt enough for oil or fuel pressure. It would be more common to have 689Kpa (100psi) or 1034kkpa (150psi). Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.