rsbda Posted October 8, 2020 Report Share Posted October 8, 2020 Hi everyone I have resently purchased a ecu master wheel speed to can adapter from brands hatch performance in the uk has any one got any info on how to get the module to talk to a link g4+ Xtreame ecu any help would be great thanks hagen Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 8, 2020 Report Share Posted October 8, 2020 Attach your tune and I can set it up. I will need to know which CAN port you are using and which wheel is connected to which input. Quote Link to comment Share on other sites More sharing options...
rsbda Posted October 12, 2020 Author Report Share Posted October 12, 2020 hi adam i thnk this is all you need if you need any thing else please give me a call at roskilda autos thanks hagen derek cobra switch setup.pclr derekwheelspeed.ltc-wheelSpeed Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 12, 2020 Report Share Posted October 12, 2020 On 10/8/2020 at 9:34 PM, Adamw said: I will need to know which CAN port you are using and which wheel is connected to which input. Quote Link to comment Share on other sites More sharing options...
rsbda Posted October 14, 2020 Author Report Share Posted October 14, 2020 Hi adam it is on can 2 the front sensors are on input 1 and 2 and the rears are on 3 and 4 I can easily swop left and right for the fron and rear in the wiring thanks hagen Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 22, 2020 Report Share Posted October 22, 2020 Sorry for the slow reply. File attached. Note you will need to use the ECU master light client to set the multiplier/divider so that the speed reads correctly. derekcobraswitchsetup CAN wspeed.pclr Quote Link to comment Share on other sites More sharing options...
rsbda Posted October 27, 2020 Author Report Share Posted October 27, 2020 hi adam is there any thing else i need to do to get this to work thanks hagen Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 27, 2020 Report Share Posted October 27, 2020 Assuming it is all wired right and you are getting valid wheel speeds or showing in the ECU master software then that should be all. I assume you have the USB to CAN programming tool. Quote Link to comment Share on other sites More sharing options...
rsbda Posted October 27, 2020 Author Report Share Posted October 27, 2020 yes i have it all working in light client i have tryed to find it on the can devices but wont show up Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 27, 2020 Report Share Posted October 27, 2020 The find devices tool is only for reprograming Link CAN Lambdas, it wont find any 3rd party devices. Do you get any wheel speeds when the wheels are turning on the misc tab of the runtimes screen? Quote Link to comment Share on other sites More sharing options...
rsbda Posted October 27, 2020 Author Report Share Posted October 27, 2020 no i dont i have tryed all four wheels i have sent you a private message with my cell number is it is easy to talk over the phone Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 27, 2020 Report Share Posted October 27, 2020 I just took another quick look. In the ecu config, change the ID on channel 3 to 1635, it looks like I made a typo when converting that from hex. Quote Link to comment Share on other sites More sharing options...
rsbda Posted October 27, 2020 Author Report Share Posted October 27, 2020 no that didnt work sorry dont know if this will help just thought it might be different to your light client Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 27, 2020 Report Share Posted October 27, 2020 Im not going to be able to help much further tonight as just about to head home, but can you take a look at the CAN 2 status on the runtimes screen like below (power off/on everything first to reboot). Are your CAN lambdas working/being found? Quote Link to comment Share on other sites More sharing options...
rsbda Posted October 27, 2020 Author Report Share Posted October 27, 2020 yes both can lamda sensers are getting picked up Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 27, 2020 Report Share Posted October 27, 2020 Ok, so that would suggest the message is making it through ok. The scaling in the ecu master manual is a bit vague, can you try changing the multiplier to 10 and divider to 1 in the Link Stream 1 like my pic below (they are opposite to this in your map currently). Quote Link to comment Share on other sites More sharing options...
rsbda Posted October 28, 2020 Author Report Share Posted October 28, 2020 hi adam i have just tryed this but it hasnt worked thanks hagen Quote Link to comment Share on other sites More sharing options...
Adamw Posted October 28, 2020 Report Share Posted October 28, 2020 Ok, sorry I'm running out of ideas, it is a bit difficult not being there. Can you grab me a photo of the "All frames" section of the light client software with a wheel turning . Also, click the "save trace" button and email me the trace file. [email protected]. Quote Link to comment Share on other sites More sharing options...
rsbda Posted October 29, 2020 Author Report Share Posted October 29, 2020 hi adam i have just sent you a email thanks hagen Quote Link to comment Share on other sites More sharing options...
ChrisUR Posted December 5, 2021 Report Share Posted December 5, 2021 sorry to dig up this thread even if it isn't too old yet did you ever figure out to get the ecumaster wheel speed can adapter to work? I plan to get one for my MR2 and run it with a G4X so it would be nice if it works before ordering Thank you !! Quote Link to comment Share on other sites More sharing options...
Adamw Posted December 5, 2021 Report Share Posted December 5, 2021 Yes, I can confirm we got this to work. It was the 2 CAN lambda channels he had set up that was upsetting things. I will attach the steam file later if I remember Quote Link to comment Share on other sites More sharing options...
ChrisUR Posted December 6, 2021 Report Share Posted December 6, 2021 excellent - would love to have this file, makes life a lot easier :-) Thank you ! Quote Link to comment Share on other sites More sharing options...
Adamw Posted December 6, 2021 Report Share Posted December 6, 2021 User stream file attached. Set up on ID1635, bit rate 1Mbit. LF wheel = CAN Freq1 RF = CAN Freq2 LR = CAN Freq3 RR = CAN Freq4. ECU Master CAN Wheel speed G4X ID1635.lcs ChrisUR and Lench 2 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.