k fuku Posted June 22, 2021 Report Share Posted June 22, 2021 About Lambda CLL Table There is only one CLL table for the two fuel tables, are there any plans to increase the number of CLL tables in future updates? Quote Link to comment Share on other sites More sharing options...
Adamw Posted June 22, 2021 Report Share Posted June 22, 2021 Do you mean the lambda target table, or something else? There is a lambda target overlay which gives you anothjer dimension of control. Quote Link to comment Share on other sites More sharing options...
k fuku Posted June 22, 2021 Author Report Share Posted June 22, 2021 On 2021/6/22 at 午後2時44分, Adamw said: Do you mean the lambda target table, or something else? There is a lambda target overlay which gives you anothjer dimension of control. There is only one CLL trim table for every two fuel tables, so it would be nice to see more in future updates. Quote Link to comment Share on other sites More sharing options...
Adamw Posted June 22, 2021 Report Share Posted June 22, 2021 You can have 2 long term trim tables to correct each bank only if you use dual channel CLL mode. There is no point using 2 long term trim tables for 2 blended fuel tables because there is no way the ecu can tell how much error is coming from each table. As an example lets say you had E50 fuel so that the ecu was operating at exactly 50% of table 1 and 50% table 2, the VE value in table 1 could be -10% wrong and the table 2 could be +5% wrong, the lambda will measure 5% lean. So the ECU over time adds +5% in both long term trim tables. If we used these long term values to correct the fuel tables this will give fuel table 1 less error but fuel table 2 more error. Quote Link to comment Share on other sites More sharing options...
k fuku Posted June 22, 2021 Author Report Share Posted June 22, 2021 デュアルフューエルテーブルは、切り替え可能なシステムとして独立して利用されます。 燃料テーブル1オン= CLL長期トリムテーブルオン 燃料テーブル2オン= CLL長期トリムテーブル2オン バンク2ソースにmathblockを使用して、それを燃料テーブルスイッチングにリンクすることは可能ですか? デジタルスイッチがオンの場合にのみラムダ1を有効にする式? Quote Link to comment Share on other sites More sharing options...
Adamw Posted June 22, 2021 Report Share Posted June 22, 2021 Ok yes, 2 long term trim tables would work for swicthed fuel tables. Switched tables are not very commonly used but I will add a request to the wish list. I dont see any way to make the 2 bank mode do what you want. k fuku 1 Quote Link to comment Share on other sites More sharing options...
k fuku Posted June 22, 2021 Author Report Share Posted June 22, 2021 2021年6月22日午後7時22分、Adamwは次のように述べました。 はい、2 つの長期トリム テーブルは切り替え燃料テーブルに機能します。スイッチテーブルはあまり使用されませんが、ウィッシュリストにリクエストを追加します。 2 バンク モードで希望どおりの動作をさせる方法がわかりません。 ありがとう。スバルのSiドライブみたいに、燃料、ラムダ、点火、電子スロットルのマップをモードごとに独立させたいですね。 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.