Peerasak T. Posted August 15, 2023 Report Share Posted August 15, 2023 I can only send 34% of configuration then PDM LINK software always stopped with below error message. Traceback (most recent call last): File "multiprocessing\process.py", line 315, in _bootstrap File "multiprocessing\process.py", line 108, in run File "linkecuapi\spawn_process.py", line 22, in ECU File "linkecuapi\__init__.py", line 216, in set File "linkecuapi\ecuapi.py", line 30, in magic File "linkecuapi\ecuapi.py", line 467, in set_setting TypeError: 'int' object is not iterable During handling of the above exception, another exception occurred: Traceback (most recent call last): File "C:\Jenkins\workspace\PDMLink Release\src\main\python\main.py", line 11, in <module> File "C:\Jenkins\workspace\PDMLink Release\build_venv\Lib\site-packages\PyInstaller\hooks\rthooks\pyi_rth_multiprocessing.py", line 52, in _freeze_support File "multiprocessing\spawn.py", line 116, in spawn_main File "multiprocessing\spawn.py", line 129, in _main File "multiprocessing\process.py", line 330, in _bootstrap AttributeError: 'NoneType' object has no attribute 'write' Quote Link to comment Share on other sites More sharing options...
craig903 Posted August 15, 2023 Report Share Posted August 15, 2023 I've had several issues with my PDM during setup. The main reoccurring issue I have is something gets corrupted and then when you go to change the mode of a pin in Pin configuration from high etc to off It instantly crashes. When the issue occurs I've tried restarting both the software and PDM, restarting my laptop, clearing app data and the only solution is to reset the PDM via the menu option under PDM in the top left corner of the software. I've also found that while there is an error and things are crashing, trying to save the configuration then wipes the configuration file and leaves it blank so I make sure I've copied the config file to a different place now. Try resetting the Pdm if you haven't and then reuploading the config to it. Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 16, 2023 Report Share Posted August 16, 2023 That error would suggest you have an empty configuration. Did you start with one of the example configurations? Can you attach it? Quote Link to comment Share on other sites More sharing options...
Peerasak T. Posted August 16, 2023 Author Report Share Posted August 16, 2023 9 hours ago, Adamw said: That error would suggest you have an empty configuration. Did you start with one of the example configurations? Can you attach it? I started from blank configuration sheet. Here is my file. Oat DVC.pdmc Quote Link to comment Share on other sites More sharing options...
Adamw Posted August 16, 2023 Report Share Posted August 16, 2023 Ok, I have attached a fixed config. The problem with your one is it was an empty config from an early software version, ie it contained settings only, but no awareness of hardware. Recent software has been changed so I dont think this trap exists anymore. The most recent software is 1.6.99, so confirm you have that on your PC. Make sure PDM firmware is up to date and this one should load correctly. You may get some errors after loading that multiple functions are connected to a pin, you can ignore these. Oat DCV fixed.pdmc Peerasak T. 1 Quote Link to comment Share on other sites More sharing options...
Peerasak T. Posted August 17, 2023 Author Report Share Posted August 17, 2023 3 hours ago, Adamw said: Ok, I have attached a fixed config. The problem with your one is it was an empty config from an early software version, ie it contained settings only, but no awareness of hardware. Recent software has been changed so I dont think this trap exists anymore. The most recent software is 1.6.99, so confirm you have that on your PC. Make sure PDM firmware is up to date and this one should load correctly. You may get some errors after loading that multiple functions are connected to a pin, you can ignore these. Oat DCV fixed.pdmc 365.75 kB · 0 downloads That fixed my problem. Thank you for your assistance. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.