Jon.C Posted April 14, 2016 Report Share Posted April 14, 2016 i have an built in G4 storm in my EVO 6. I dont Get any signal out from any of the aux outputs, it only works when i choose to use the test function. Then i got both high and low signals. I want to controll fuel pump. When its all hooked with relay controlled by low side of ecu it wont prime ore anything, also tested while crankingCan anybody give some tips? Quote Link to comment Share on other sites More sharing options...
Steve Posted April 14, 2016 Report Share Posted April 14, 2016 Post your pcl and let us have a look Quote Link to comment Share on other sites More sharing options...
Jon.C Posted April 14, 2016 Author Report Share Posted April 14, 2016 Post pcl? How? Post your pcl and let us have a lookPost pcl? How? Quote Link to comment Share on other sites More sharing options...
Steve Posted April 14, 2016 Report Share Posted April 14, 2016 Unnless its fixed this forum wont let us post a pcl file extension. But you can attach it as a zip file. Or use a file host service. Quote Link to comment Share on other sites More sharing options...
Jon.C Posted April 14, 2016 Author Report Share Posted April 14, 2016 (edited) Unnless its fixed this forum wont let us post a pcl file extension. But you can attach it as a zip file. Or use a file host service.see attachment for pcl file, hope you have time to take a look at it as soon as possible, because i have dyno run cooming up soon. Thanks in advance Edited April 15, 2016 by Jon.C Removed pcl file Quote Link to comment Share on other sites More sharing options...
Steve Posted April 14, 2016 Report Share Posted April 14, 2016 I pressume you are trying to use AUX 1 as fuelpump? The one set to "test" in the PCL?I see that you ALSO have ignition drive 3 set up for fuel pump. You can only have one output designated to this so you need to switch that one off.. Quote Link to comment Share on other sites More sharing options...
Jon.C Posted April 14, 2016 Author Report Share Posted April 14, 2016 Correct about aux 1 for fuel pump. I Know i can only use one, but this pcl file you got was only a test with allot of different stuff. Im sure what you mentioned now is not the problem. Quote Link to comment Share on other sites More sharing options...
Steve Posted April 14, 2016 Report Share Posted April 14, 2016 (edited) Have you tried to hook it up to a different output? like aux 8 or something.Could be some bug sor something. Also, are you getting RPM reading and "yes" on both triggers when cranking? Edited April 14, 2016 by Steve Quote Link to comment Share on other sites More sharing options...
Jon.C Posted April 14, 2016 Author Report Share Posted April 14, 2016 I tryed different outputs, same issue. I have not checked both signals while cranking, but if any help the car starts fine with fuel pump direct on 30 power. Quote Link to comment Share on other sites More sharing options...
Simon Posted April 14, 2016 Report Share Posted April 14, 2016 You need to make sure that the is only one output assigned as fuel pump.If two are assigned the same function one will not work.To help we need to see the file exactly as you are trying to use it. Quote Link to comment Share on other sites More sharing options...
Jon.C Posted April 15, 2016 Author Report Share Posted April 15, 2016 You need to make sure that the is only one output assigned as fuel pump.If two are assigned the same function one will not work.To help we need to see the file exactly as you are trying to use it.OK, i tryed disabled all outputs and assigned one output to fuel pump. I have also tried different pins, aux 5-6-8-1 has Been tested. All of them act in the same way. Quote Link to comment Share on other sites More sharing options...
Scott Posted April 15, 2016 Report Share Posted April 15, 2016 Please see the following video to see how to record PCLog and how to save your base-map:Then either upload the files on the forum or email them to [email protected]. If emailing them please include a link to this forum thread so we know what the files are for. Quote Link to comment Share on other sites More sharing options...
Jon.C Posted April 15, 2016 Author Report Share Posted April 15, 2016 Hi, i found some earth cables that is not to good, i fixed this and the problems is now ok! Now im happy!!Thanks for all of the help! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.