Power Posted February 13, 2018 Report Share Posted February 13, 2018 Hi Guys I need to know the pinouts of Electronic throttle and Foot position sensor Subaru Someone to help me ? Best Regards Quote Link to comment Share on other sites More sharing options...
cj Posted February 14, 2018 Report Share Posted February 14, 2018 Colours will vary by year but pins should be the same. Heres what it is on a 2005 Legacy Pedal 1 LY +5v 2 R Signal Sub 3 GB +5v 4 L Ground 5 B Signal main 6 YG Ground Throttle 1 W D4 Motor - 2 B D5 Motor + 3 LW Ground 4 R C29 signal sub 5 P C16 +5v 6 W C18 signal main Quote Link to comment Share on other sites More sharing options...
Power Posted February 14, 2018 Author Report Share Posted February 14, 2018 Hi cj Thank you very much for your reply...........for be sure, please confirm to me the number position ......see the pics down Quote Link to comment Share on other sites More sharing options...
cj Posted February 14, 2018 Report Share Posted February 14, 2018 The ethrottle itself is certainly that because of the big black and white wires. I don't imagine the service manual would change half way through so the pedal is likely the same. (looking into the connector, clip at the top) Quote Link to comment Share on other sites More sharing options...
Adamw Posted February 15, 2018 Report Share Posted February 15, 2018 Most connectors will have the pin numbers moulded into them, clean them up and take a closer look. Quote Link to comment Share on other sites More sharing options...
Power Posted February 15, 2018 Author Report Share Posted February 15, 2018 Thanks Again have a great day Quote Link to comment Share on other sites More sharing options...
Stevieturbo Posted February 23, 2018 Report Share Posted February 23, 2018 There are definitely a few variations of pedal pinout depending on which pedal and model. When i did mine I found a few online and none matched the STI Pedal I used ( same main plastic body but with a steel arm for the pedal ). And my pinout is different than listed above. Best way to find out is to get a power supply or battery or similar and test it before hooking up to the ecu Quote Link to comment Share on other sites More sharing options...
mapper Posted April 25, 2018 Report Share Posted April 25, 2018 On 2/23/2018 at 9:58 PM, Stevieturbo said: There are definitely a few variations of pedal pinout depending on which pedal and model. When i did mine I found a few online and none matched the STI Pedal I used ( same main plastic body but with a steel arm for the pedal ). And my pinout is different than listed above. Best way to find out is to get a power supply or battery or similar and test it before hooking up to the ecu Can you please send me your Pinout. I have a same steel arm pedal. Thank you in advance. Quote Link to comment Share on other sites More sharing options...
barge Posted April 25, 2018 Report Share Posted April 25, 2018 If it's from an impreza it's pretty easy to find a service manual for pretty much every year mode online. Quote Link to comment Share on other sites More sharing options...
Remski Posted April 26, 2018 Report Share Posted April 26, 2018 Here is the pin-out I used. Throttle body is off 2005 sti.. (note.. I had to switch pins aux9 and aux10 around since the plate was closing not opening.) Throttle body Main An Volt 3 Pin 6 on connector Pin 18 on the ECU main circuit Throttle body Sub An Volt 2 Pin 4 on connector Pin 29 on the ECU sub circuit Throttle body ECU +5V Pin 5 on connector Pin 16 on the ECU +5V Throttle body Sensor Ground Pin 3 on connector Throttle body Throttle Motor - Aux 9 Pin 1 on connector Pin 4 on the ECU Throttle body Throttle Motor + Aux 10 Pin 2 on connector Pin 5 on the ECU And here is the accelerator pedal. Same thing .. off 2005 sti. Accelerator Pedal Throttle pedal Sensor Ground Pin 6 on connector Throttle pedal Main Pin 5 on connector Pin C17 on ECU Throttle pedal Ground Pin 4 on connector Pin C34 on ECU Throttle pedal ECU +5V Pin 3 on connector Pin C15 on ECU Throttle pedal Sub Pin 2 on connector Pin C28 on ECU Throttle pedal ECU +5V Pin 1 on connector Orange denotes shielded cable that I used. Quote Link to comment Share on other sites More sharing options...
Stevieturbo Posted May 6, 2018 Report Share Posted May 6, 2018 Not sure exactly which year although obviously it'd need to be 05-07 in the UK Subaru pedal, metal arm....plastic/rubber pedal. So possibly not an STI pedal. Looking into pedal, clip on top ( These were wiring colours on the plug that was cut from loom ) Left =1 1- Dark Blue = Signal 2- Orange = Sensor Ground 3- Blue/Red = 5v 4- White/Blue = Signal 5- White/Red = Sensor Ground 6- Light Blue = 5v Both are 0-5v tracks upwards But with a 5v supply it's pretty easy to work through them and test yourself. I did buy another pedal for a spare that I think came from a Legacy, different wire colours, same plug, and testing showed same pinouts. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.