don17
Members-
Posts
69 -
Joined
-
Last visited
-
Days Won
1
Content Type
Profiles
Forums
Events
Gallery
Blogs
Everything posted by don17
-
It has only started doing it recently, which is strange
-
New issue with the car, when the engines warm 80-90 degrees. When turning the key to start position, fuel pump continues to pump/prime until started. I have dropped the pre crank times very low still continues to do it? Signs of a bad fuel pump ecu ? Any help appreciated, only started happening recently,
-
I have a g4+ supralink non vvti ecu, can I wire 2 pin non vvti ignition coils straight into IGT pins and ground without going through external igniter? Or do I need a new igniter
-
Can these instructions be posted again please Hi can you re upload the instructions
-
Just wondering the best way to start or a base to start with my iacv settings, factor 6 pin sensor, 90mm throttle body, distributor for the moment coil packs soon
-
Perfect thanks for the info, I'll touch base again when I'm changing everything over
- 6 replies
-
- 2jzge na-t
- 2jzge
-
(and 2 more)
Tagged with:
-
No worries I get what you mean, The G4+ supralink
- 6 replies
-
- 2jzge na-t
- 2jzge
-
(and 2 more)
Tagged with:
-
I haven't installed crank sensor yet and I want to remove distributor completely, won't I need to re setup the triggers? Also what pin can I use as sensor ground for crank ground
- 6 replies
-
- 2jzge na-t
- 2jzge
-
(and 2 more)
Tagged with:
-
Just looking for some guidance on a base map for the car. In a week or 2 I will be installing x6 2jzgte VVTI coils on my NA-T . It's 2jzge-t currently with a distributor, has single turbo I will be using cam sensor trigger kit and Gte oil pump with crank sensor with 2JZGTE crank gear, latest-edit.pclr
- 6 replies
-
- 2jzge na-t
- 2jzge
-
(and 2 more)
Tagged with:
-
Okay, I'm not 100% sure which wire is -VE (ground) .Also pin B57 has +12V? In that correct becuase 2/5 pins have +12v or (2/3 have +12v) pins you have listed
-
Currently setup old igniter (comes stock with car) as far as I can tell the grounds are good. The previous igniter I had in actually had a ground wire but it was tucked underneath. The current stock igniter might ground through the body but seems to be good
-
No worries Adam, I have rewired the original igniter becuase @ThatSupraGuyhas sent me a base map and he's using a stock igniter and his trigger setup looks good. The file above ^ Just wiring up now and gonna try crank
-
how to i see realist rpm? just seeing if the rpm is moving at all in the software? think it uses the signal from 1 for all 6? when i go to test the igniter in test mode it doesnt spark. diagram below is how i had it wried up. I think i do have the original 2JZ GE 4 pin ignitor around Toyota Supra.pclr
-
just bought a link ecu g4+ and was going through start up guide. MY build is 2jzge- turbo Supra JDM 1993 , map sensor calibrated, tps not calibrated (wiring issues). when i crank the engine there is no spark from main coil going to distributor cap. Originally running a piggyback system with the Aristo 2JZGTE ecu which was running fine, unplugged earlier today, current ignition module is rewired to work with distributor because the 2jzGTE uses COP instead of distributor (old setup). In the ignition settings neither direct spark or distributor have any spark. also unsure about what trigger setup to use, when cranking trigger signal status 1 is on/active Was previously running fine before installing new ecu