cHeMiCaL_
Members-
Posts
17 -
Joined
-
Last visited
cHeMiCaL_'s Achievements
-
Hi, I am upgrading my G4+ Fury to Fury X. Is there any automation apps to convert my G4+ (PCLR) maps to the latest generation X (PCLX)? It's very difficult to do it manually. thank you.
-
Vaughan reacted to a post in a topic: Advise on setting for 140 Bar Press Sensor (101-0186) for brake & clutch pressure sensor
-
cHeMiCaL_ reacted to a post in a topic: G4+ Fury - Gear Detection Problem / Gear Ratio Calc not working
-
Noted with thanks @Adamw! Speed sensor works fine as i can see it through my MXP dash all this while. Let me diagnose everything again. much thanks for all of the advices! cheers!
-
ok @Adamw i will retry again when the situation permits. My driven LF wheel speed source is assigned and working well. for the gear ratio calc reported in first gear is 655.35
-
Yes adam, ive read through and followed all the instructions in the manual. I’ve not been lucky with my ecu and been getting loads of issues since beginning. I still hv warranty ticket open btw and hvnt got the chance to this return to your warranty team. the problem i hve now, even before i can get up to 15km/h, it will report ‘finished’, where it should be reporting unsuccessful. Whether it’s 15km/h or 0km/h it will report ‘finish’ after 3 seconds of running and i will get status gear ‘1’ and thats abt it. I hope my explanation gives better picture on my current situation. Much thanks! thanks Vaughan, will take that as a consideration surely!
-
Hi @Adamw, Need your assistance, Am using G4+ Fury and i cant get my gear detection to work. When i initiate the gear calibration (through ECU Calculated), the Gear Ratio Status' "Calculating Gear" will always display "Finished" after 3 seconds even though i am not moving. This problem applies to all 5 gears. Can you please help to manually enter my gear ratio as per below? currently its full lockdown in my hometown, so i cant go out for a drive to do logging for you. I have also attached my config files for your perusal. 1st Gear (2.875) 2nd Gear (1.950) 3rd Gear (1.444) 4th Gear (1.096) 5th Gear (0.825) Reverse (3.416) Final Ratio (4.111) Circumference: 2052.09 mm hear from you and many thanks kindly for your help, @Adamw! cHeMiCaL_ 01Jun2021.pclr
-
the temp increase when i run the engine but they only increas upto around 33°C. is there anyway i can calibrate inside the linkecu itself? thanks for helping @Adamw!
-
Yes, they’re reading the same. I have replaced the EGT sensors twice yet still reading the same.
-
Hi @Adamw! Happy new year! Need help with my Ecumaster EGT to CAN with my G4+ Fury setup. After following all the instructions and setting up the can stream to the letter, my EGT reading for 5 sensors seems to be wrong (too low). Any way you can advise and help me out? screen capture for your perusal as per-below! thanks @Adamw!
-
thank you @Adamw!!!!
-
cHeMiCaL_ reacted to a post in a topic: Digital Input State Via CAN
-
Hi @Adamw, sorry to trouble you again. I have a total of 5 EGT. 4 for the cylinders and 1 for the downpipe. Can you please add another 1 EGT for my display to read please? the files that you provide only support upto 4 EGT. Thank you!
-
thank you very much @Adamw! will load these files soonest!
-
Hi @Adamw, here you go. attached are my ecu and dash's config. feel free to add or change anything. Appreciate your help again. rgds. chemical_fury_021220.pclr chemical_mxs_strada.zconfig