gtr-import Posted April 21, 2020 Report Share Posted April 21, 2020 Hello everybody, Need to fill some data on my link plug in ECU to use the modeled multi fuel mode , I use 1200cc on my R32 GTR from DW , just ask them to provide accurate data to fill the dead time table and pulse width table and they provide me the following information , don't know if I can use it , because they don't seem to be usefull on the link G4+ what do you think ? https://www.deatschwerks.com/sites/www.deatschwerks.com/files/DATA/injectordata/42M%201200cc%20Technical%20Data%20Sheet.pdf tanks for the reply Quote Link to comment Share on other sites More sharing options...
dx4picco Posted April 21, 2020 Report Share Posted April 21, 2020 Well I am not sure your plugin ecu is going to run those low impedance injectors. as far as I know plugins do not have peak and hold injector drivers required for it Quote Link to comment Share on other sites More sharing options...
Adamw Posted April 21, 2020 Report Share Posted April 21, 2020 4 hours ago, dx4picco said: Well I am not sure your plugin ecu is going to run those low impedance injectors. as far as I know plugins do not have peak and hold injector drivers required for it GTR's have low imp stock and have a ballast resistor in series so they should work. The DW ones appear to be a little lower resistance than stock though. 5 hours ago, gtr-import said: just ask them to provide accurate data to fill the dead time table and pulse width table and they provide me the following information Obviously there is no short pulsewidth adder data so leave that table set to zero. For the deadtimes I would use the "driver A" data as it will be closer to how the saturated drivce works but it likely wont be perfect. Quote Link to comment Share on other sites More sharing options...
kaptainballistik Posted January 27, 2021 Report Share Posted January 27, 2021 I found the Data is under the GM SPA Tab in the https://www.deatschwerks.com/gm-calibration-data, files, Specific data for the 1200's is under https://www.dropbox.com/s/g089z5pv7uvigkx/GM injector data 16mx-1200.xls Hopefully Its helpful... "call" PW limit 0.0000 0.1250 0.2500 0.3750 0.5000 0.6250 0.7500 0.8750 1.0000 1.1250 1.2500 1.3750 1.5000 1.6250 1.7500 1.8750 2.0000 2.1250 2.2500 2.3750 2.5000 2.6250 2.7500 2.8750 3.0000 3.1250 3.2500 3.3750 3.5000 3.6250 3.7500 3.8750 4.0000 "adder" PW 2.8750 0.1000 0.0375 -0.0342 -0.0943 -0.1296 -0.1373 -0.1334 -0.1318 -0.1227 -0.1127 -0.1057 -0.0962 -0.0682 -0.0673 -0.0603 -0.0454 -0.0238 -0.0236 -0.0162 -0.0096 -0.0073 0.0031 0.0186 0.0058 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000 AI10 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.